Finished my Ball polisher

[Strokerz]

I finished the homemade ball polisher I was going make over a month ago today and I have to say so far it works great! You can polish 8-10 balls at a time it's fast and quiet and is better than doing it by hand or spending $300-$600 for one. Total cost $25.00 + polish. Total time 2 hrs drive time included. Thanks skins for the plans! I am using the Arimath ball polish because I have like 3 bottles of it. Any one looking for an inexpensive ball polisher should try this.

[TannerPruess]

Post some instructions or are you selling them?

[pip9ball]

I second that...i've been wanting to build one myself. Can you please post instructions and materials?

[krbsailing]

I think there might be a link here somewhere with instructions :rolleyes: ....memory is failing :eek:

My recollection is that you need an everyday car polisher, round plastic bucket with a lid, some plush/pile carpeting, glue, razor blade and, something (at least in this example) like a 3/4" piece of plywood for a divider!?

If possible, please refine the parts list with a little instruction. Thanks :)

[Strokerz]

Post some instructions or are you selling them?
Here's how I built it, I got these instructions from skins.
Materials
5 gal bucket Lowes $5
10 inch orbital car polisher with round handel K-mart $20.00
Short nap carpet Free from friend who owns carpet company
3m spary glue had some alreday but cost bout $10 a can and lasts forever
1 piece of 2x6 scrap wood or plywood would work also
some long wood screws
The pics I am posting are from my model. Skins plans called for you to use zip ties to hold the polisher in the bucket but I found I didn't need them mine fit pretty snug so I didn't use them but you could
Tools
Carpet knife
Power drill
Power saw
1st step
Cut hole in the bottom of the bucket for plug
put polisher in upside down with the cotton pad on the wheel of the polisher
I switched the on/off switch to the on position
measure your carpet and cut to length. Use spray glue to hold it in place. When gule is dry take your 2x6 cut it to length mine was about 11 1/4 inch
Take carpet cut it to cover top and both sides if wood. Use spray glue to hole carpet to the wood.
Take the carpet covered wood and put in the bucket. Make sure it fits snug but dosen't touch the pad of the polisher but it just sits about 1/4 inch above it. Then take your wood screws and fron the ends screw the wood to the bucket. I used one screw on each end it holds just fine. Your ready to polish. I turn on the machine put the balls in 4 on each side and put a few drops of ball cleaner on the balls while they are spinning. I am thinking about making a cabinet for it to sit in out of plywood to make it look more professional;) I use an extension cord pluged into a power strip for the on/off switch. It takes about 3-5 minutes depending on how dirty the balls are. About 2 minutes for our sets. Any questions feel free to ask

[Strokerz]

These are pics of mine. I will post pics of skins when I find them

[JimS]

Wouldn't it work better if there were some downward pressure on the balls? How about a lid with a piece of wood as a divider, maybe a 2x2 attached to the lid, instead of the divider wood in the bucket?

Attached to the underside of the lid and the wood would be some sort of material to polish the balls.... lambs wool, felt, foam, carpet, other?

Might need to drill some holes in the bottom of the bucket to somehow tie down the orbital polisher.

Other ideas?

[TheHole]

I will snap some pics of mine tomorrow....we built with the buffer but I built a box out of wood to hold it. Added an on/off switch. And made a clear plexiglass top with handle to close off the top. You will see in the pics of mine that I added a small piece to the middle of the plexiglass that polished the balls in the middle of the polisher. Mine will hold a full rack of balls and works like a charm.

[Strokerz]

Can't wait to see pics!

[JimS]

I will snap some pics of mine tomorrow....we built with the buffer but I built a box out of wood to hold it. Added an on/off switch. And made a clear plexiglass top with handle to close off the top. You will see in the pics of mine that I added a small piece to the middle of the plexiglass that polished the balls in the middle of the polisher. Mine will hold a full rack of balls and works like a charm.

Waiting and wishing for pics and such! Thanks.

[scottycoyote]

im going to have my home table set up soon as tax season is over. Not knocking your plans, it seems like a cool idea and a great way to save some money, which im all for. My question is, is that something you really need or is it just a cool gadget. Can i just polish my balls by hand (man that sounds dirty). Do my balls really need polishing, or can you just wipe em down lol.

[mnShooter]

I clean my balls with a wet rag in the sink and rinse them off and dry them with a towel. When you put polish on them they seem to get dirty a lot faster. They don't get as shiny but that only lasts a couple racks anyways.

[Strokerz]

We have 11 sets of Super pro balls and it is time consuming to polish all 11 sets by hand. 2 or 3 sets not so bad but 11 once or twice a week yeah I needed a polisher. I had see these plans posted here so i decide to give it a whack. Turned out good I'm happy got $25 invested in athing that makes my life a little easier:D Cleaner balls longer cloth life better playing conditions!

im going to have my home table set up soon as tax season is over. Not knocking your plans, it seems like a cool idea and a great way to save some money, which im all for. My question is, is that something you really need or is it just a cool gadget. Can i just polish my balls by hand (man that sounds dirty). Do my balls really need polishing, or can you just wipe em down lol.

[Strokerz]

Either way I suppose is fine as long as their clean I guess. but the polish makes them look real shiny. Nice for tourneys and such!
im going to have my home table set up soon as tax season is over. Not knocking your plans, it seems like a cool idea and a great way to save some money, which im all for. My question is, is that something you really need or is it just a cool gadget. Can i just polish my balls by hand (man that sounds dirty). Do my balls really need polishing, or can you just wipe em down lol.

[Cornerman]

Wouldn't it work better if there were some downward pressure on the balls? How about a lid with a piece of wood as a divider, maybe a 2x2 attached to the lid, instead of the divider wood in the bucket?

I made one several years ago and the weight of the balls was enough pressure.

The divider (in my case, I had individual pockets) keeps the balls in place spinning madly against the cleaning pads.

Fred

[Strokerz]

I made one several years ago and the weight of the balls was enough pressure.

The divider (in my case, I had individual pockets) keeps the balls in place spinning madly against the cleaning pads.

Fred
Thats another idea instead of the divider a series of pockets the size of the ball so they could spin individualy would shine them better I think. Kinda like the Diamond design

[Strokerz]

So i'm working on making a ball polisher for a pool room across town I'm almost finished except for installing the divider when a bright idea hits me. hey try it with out the divider and see what happens. So I do and I have to say I am pretty happy with the result I think it works better this way then with the divider. The balls spin better abd faster and the carpet lining contacts more surface with the balls. With the divider you had to as some of us have noticed here ya might have to jossle the balls a bit by hand to get the to move around alot with the divider. This way they move freely. I know your gonna say won't the balls rub against each other? Not really at all. I fuigered they would but they stay pretty evenly spread when doing 8 balls at a time. Total time for a rack about 4 minutes. I will post pics tonight of it in action. .

[Scottster]

On mine, I built a top polisher.

I used a 3" diameter clear plastic "trinket" holder (Walmart craft section) and then but (8) 4" dowells and screwed them to the trinket holder.

Initially, I was going to use it to space the balls apart. But after gluing the carpet to the dowells, there wasn't enough room. So instead, I used the spare buffing cover that came with the orbital polisher, and stretched it over the contraption, creating a lid.

I thien put 8 balls in the polisher, put the top on and add 4 balls for weight. It works incredible, and the balls stay in place. They dont rub each other.

[Strokerz]

Cool! Sound like a good Idea!

[NateSchoepf]

this is great, thanks

[JimS]

On mine, I built a top polisher.

I used a 3" diameter clear plastic "trinket" holder (Walmart craft section) and then but (8) 4" dowells and screwed them to the trinket holder.

Initially, I was going to use it to space the balls apart. But after gluing the carpet to the dowells, there wasn't enough room. So instead, I used the spare buffing cover that came with the orbital polisher, and stretched it over the contraption, creating a lid.

I thien put 8 balls in the polisher, put the top on and add 4 balls for weight. It works incredible, and the balls stay in place. They dont rub each other.

The mental picture of this is just not coming through for me. Couldl you post a picture? Thanks. Jim

[Strokerz]

I'll post pics as soon as i get to the room today

[n10spool]

I think he means in a star pattern 3" circle with 8 arms screwed to the outside of the trinket holer ie.. i 3" pipe. he can polish 8 balls at a time. nice idea.

[JimS]

I'll post pics as soon as i get to the room today

Would love to see the pics as I can't visualize what you built.

[Strokerz]

It's a pretty simple design

[Strokerz]

a few more pics

[JimS]

On mine, I built a top polisher.

I used a 3" diameter clear plastic "trinket" holder (Walmart craft section) and then but (8) 4" dowells and screwed them to the trinket holder.

Initially, I was going to use it to space the balls apart. But after gluing the carpet to the dowells, there wasn't enough room. So instead, I used the spare buffing cover that came with the orbital polisher, and stretched it over the contraption, creating a lid.

I thien put 8 balls in the polisher, put the top on and add 4 balls for weight. It works incredible, and the balls stay in place. They dont rub each other.

It's this one I'm curious about and can't picture. Can you post a picture? Sure would appreciate it. Thanks, Jim

[Scottster]

It's this one I'm curious about and can't picture. Can you post a picture? Sure would appreciate it. Thanks, Jim


Hi Jim, I will try to get some pics up. I am not too savvy on that type of thing. I have done it before, but it has been awhile I will try and figure it out.

[JimS]

Hi Jim, I will try to get some pics up. I am not too savvy on that type of thing. I have done it before, but it has been awhile I will try and figure it out.

If you can get'r done it will be appreciated. :D