Ebony / Maple 8 Pointer

RDCustomCues

AzB Silver Member
Silver Member
Here is a nice 8 pointer I completed around Febuary of this year. I played with it as my personal cue since then. Its time for a new home. Original asking was $550 Has some minor run marks around the joint from case I was carrying in to the pool hall and a little bluing on the shaft. It plays really well Ivory Ferrule Specs are below. $400 Shipped is the asking price paypal preferred. SOLD
Specs

Shaft Specs
1 shaft
Ivory ferrule
Everest layered tip
13 mm
Pro taper
3.9 ounce
29.5 inches

Butt
Ebony forearm
8 Maple points 4 high 4 low 4 high has purple / green / purple veneers
Maple Butt sleeve with deco rings
Elforyn joint with deco ring / fiber ring and phenolic ring
Elforyn buttplate
Black Leather wrap
15.6 ounces
29.5 inches
Total weight - 19.5oz

Shipping in Cont US FREE
Paypal Perferred No Charge

8pointer1.jpg
 
Last edited:
I remember when you were selling this cue a while back.

What I don't get is why you put the black above the butt plate and not under the wrap too.

Kind of makes the cue look funny in the sleeve. You see what I'm talkin about right?

I like the overall design of the cue though with the exception of that. Nice lookin..

I mean no offense so dont take it that way.
 
Ebony and Maple

Super nice looking cue! The figuring in the maple is crazy. The ebony really makes the curly maple points jump out. Sharp cue at a great price.

I think he did the black ring on the butt (position E) to balance with the joint ring (position B). The rings on either side of the wrap are identical (positions C&D).
 
RDCustomCues said:
Here is a nice 8 pointer I completed around Febuary of this year. I played with it as my personal cue since then. Its time for a new home. Original asking was $550 Has some minor run marks around the joint from case I was carrying in to the pool hall and a little bluing on the shaft. It plays really well Ivory Ferrule Specs are below. $400 Shipped is the asking price paypal preferred.
Specs

Shaft Specs
1 shaft
Ivory ferrule
Everest layered tip
13 mm
Pro taper
3.9 ounce
29.5 inches

Butt
Ebony forearm
8 Maple points 4 high 4 low 4 high has purple / green / purple veneers
Maple Butt sleeve with deco rings
Elforyn joint with deco ring / fiber ring and phenolic ring
Elforyn buttplate
Black Leather wrap
15.6 ounces
29.5 inches
Total weight - 19.5oz

Shipping in Cont US FREE
Paypal Perferred No Charge

8pointer1.jpg
Nice looking cue.
What do you mean by minor runs? (scuffs from the case or runs in the finish when cue was sprayed)
What is the pin size? Is it a flat faced joint?
Any chance that there could be a second matching shaft available for a reasonable fee?

Thanks,
Mike H.
 
Wow, one of the nicest cue that I've seen in awhile in that price range. I hope I get my insurance money from USPS soon so I can snatch this up. Good luck with the sale if I can't get the money up soon enough.
 
cyrex said:
Super nice looking cue! The figuring in the maple is crazy. The ebony really makes the curly maple points jump out. Sharp cue at a great price.

I think he did the black ring on the butt (position E) to balance with the joint ring (position B). The rings on either side of the wrap are identical (positions C&D).

Right On Thats Correct
 
Nine Ball said:
I remember when you were selling this cue a while back.

What I don't get is why you put the black above the butt plate and not under the wrap too.

Kind of makes the cue look funny in the sleeve. You see what I'm talkin about right?

I like the overall design of the cue though with the exception of that. Nice lookin..

I mean no offense so dont take it that way.


The sleeve looks great to me. I dont understand how it didnt sell when it was brand new and I dont know how its still available now with only a few months on it. Bump for a cool dude and a nice stick!
 
powerlineman80 said:
The sleeve looks great to me. I dont understand how it didnt sell when it was brand new and I dont know how its still available now with only a few months on it. Bump for a cool dude and a nice stick!


Thank you for the kind words. I sold a Titlist conversion on here I was playing with and took this off the market and used as a personal player. I just finished about a dozen more cues that were sold except one and I have swithched to it. No use in it sitting in a case
 
Henny HaHa said:
I could be interested if I could get some responces to previous questions?:(
Thanks.

I totally appologize I must have head up rear syndrome and did not even notice your post.

What do you mean by minor runs? (scuffs from the case or runs in the finish when cue was sprayed)
Rub Marks from a case not runs. sorry its scuffing
What is the pin size?
3/8x10
Is it a flat faced joint?
Yes
Any chance that there could be a second matching shaft available for a reasonable fee?
Yes

weight bolt? yes on this cue

If i missed anything let me know

Sorry last few days have been crazy bought new truck so I did not follow this thread as close as I needed i just responded mainly to PMs.
 
Last edited:
that is alot of cue for the $$$. it has my vote, unless you want a Cue-Tec<-----just kidding, :eek: ;)


seriously thats one hell of a cue for the $$$, when you consider what custom cues typically cost, this is a steal. getting the specs, that nice of wood, details, working with the guy who built it etc for that price it is a gift. I would be all over it, if i needed a cue.
 
Back
Top