Changing My Own Tip

Heres the best thread that I have come across.

http://forums.azbilliards.com/showthread.php?t=51018

Take it to you friendly neighborhood cue repair person. They'll do a professional job and you can probably stand there and watch while they do it.

For the $20 to $30 some odd bucks is may cost depending on what tip you want, it's worth it to have it done right and not mess with it. Unless you want to invest in a small repair lathe and tools for just a hobbie like I did you will be better to take it to a repairman so it's done right <<ED

johnny, there isn't a thing wrong with wanting to learn do-it-yourself tip installing, but the reasons why I always suggest that the work be done by your friendly neighborhood repair person are (1) they'll do a professional job, and (2) they have to put beans on the table just like all the rest of us do.

Take it straight to Jim Buss's shop.

STLJohnny, I would suggest that you take it straight to Jim Buss. He will replace the tip while you wait. He is a real gem in St. Louis. He has alot of knowledge and happily shares it with his customers. I have been a satisfied customer for 10 years, if that means anything. BTW 12 dollars for most tips is the charge. Sportscenter also does tips if they are closer to you, not sure of the quality there as I am loyal to Jim Buss

DoubleD said:

You don't need a lathe. In fact, you are more likely to screw up using a lathe. I only use three tools--file, razor blade, sandpaper. I've never damaged a shaft.

Every pool player should learn how to change a tip, just like every driver should be able to change a tire and their oil.

Click to expand...

Well said. I too used only a razor and sandpaper, but then got a Tweeten Rapid Cue Top Sander. This is not rocket science, and I the only cue that has been in any of my three (3) metal lathes had a phenolic tip/ferrule that a buddy wanted faced-off for a regular tip.

Dave

stljohnny said:

So... I keep reading that a lot of people do their own tips, and from what I can see - it's not that difficult. However, I have some questions about the process.

I went through the Ask The Cuemaker forum and didn't see it there - and you can't search for "how to install tip" because "how, to and tip" are too short and get excluded from the search.

1) I've heard that superglue is NOT the glue you want to use (I actually didn't even know that the tips were glued on, lol). I saw one mention of Gorilla White - is that the preferred glue?

2) I don't have a lathe, nor access to one. How much of problem is that going to be?

3) I would like to try a Kamui tip - but it appears I can't buy them, so I guess I'll try something else. A Moori perhaps?

4) I only have one playing cue, so if I F--- it up, I'm screwed, should I just forgo the hassle and keep taking it to my local place?

5) Is there a thread here or somewhere (easily found) that gives a good set of instructions?

Click to expand...

Why can't you buy a Kamui? http://www.azbmarketplace.com/products/Black_Kamui_Pool_Cue_Tips-100201-80.html ... For sale right here on AZB.

Also, for what it's worth, I did not like Moori when I tried it. Try the new Tiger Onyx and us all know what you think.

Change own tip

Pm sent with some helpful tips on how to

stljohnny said:

So... I keep reading that a lot of people do their own tips, and from what I can see - it's not that difficult. However, I have some questions about the process.

I went through the Ask The Cuemaker forum and didn't see it there - and you can't search for "how to install tip" because "how, to and tip" are too short and get excluded from the search.

1) I've heard that superglue is NOT the glue you want to use (I actually didn't even know that the tips were glued on, lol). I saw one mention of Gorilla White - is that the preferred glue?

2) I don't have a lathe, nor access to one. How much of problem is that going to be?

3) I would like to try a Kamui tip - but it appears I can't buy them, so I guess I'll try something else. A Moori perhaps?

4) I only have one playing cue, so if I F--- it up, I'm screwed, should I just forgo the hassle and keep taking it to my local place?

5) Is there a thread here or somewhere (easily found) that gives a good set of instructions?

Click to expand...

A couple of thoughts:

First, invest in a Williard's Classic Tip-Trimmer -- it's the block of machined metal that comes with collets and nicely trims the tip. (And no matter what anyone claims, almost every tip out there mushrooms a bit.) Though a bit of an expensive initial outlay, over the ten years or so that I've owned one, I have found it invaluable.

Second, have your tip professionally installed with a pad, black or red.

Third, buy yourself a small supply of quality tips.

Fourth, after the professionally installed tip wears out, carefully razor-blade off the old tip, sand down the pad a bit and glue on a new tip yourself.

Fifth, use Tweeten's glue -- it's water soluble. And, if you use it right and let dry overnight, it's more than up to the task of keeping a tip on. Do not use super glue -- you'll get it all over your ferrule and won't be able to get it off. Don't use Gorilla glue, I think we talked about that one on RSB a long time ago and someone reported that it expanded when curing (big glue line).

Last, use your Williard's to trim your tip. Used correctly, you won't touch your ferrule and you'll have a nicely trimmed tip.

If you don't sand down the pad excessively, you should be able to use for a few years for multiple tips.

Lou Figueroa

stljohnny said:

It's a drop-off kind of thing. The place I take it has Jim Buss do the tips, he comes by every other day to pick up/drop off cues/shafts, so...

I just watched the "how to" video for the seyberts cue tip replacement kits...that looks pretty darn good.

Click to expand...

Actually, though I could be wrong, I don't think Jim does the tip jobs. His brother, George, does them. Not that there's anything wrong with that. George is pretty meticulous.

Lou Figueroa

DELETED. .. Do it his way <<LOL

I once replaced a tip with no problem.A little lite sanding and some Tweentens.
Then i tried to do it again at a later date and the tip i had was wider then the shaft size.I couldn't razor off the excess without a lathe so i took the tip off and brought it to a pro.
Its a lot easier and there is no worrying that it is done correctly.
I will never try to replace a tip again myself.

stljohnny said:

that's exactly why i was wondering about it. I'm fairly handy with tools and whatnot - but the first time is always a little... scary. I think I'll see if I can get some practice in by replacing tips on the house cues at my local place. they always have some to do and won't turn away free labor. haha

Click to expand...

Yea thats what I would do and I originally posted. I was just saying from my experience. Some just try to save money but in the long run it may wind up costing them more then it would have been to get it done right the first time , Good luck to you and Im sure you can buy kamui's at different place's check around you will find them <<ED

DoubleD said:

Totally disagree with everything you just said.

You don't need a lathe. In fact, you are more likely to screw up using a lathe. I only use three tools--file, razor blade, sandpaper. I've never damaged a shaft.

Every pool player should learn how to change a tip, just like every driver should be able to change a tire and their oil.

dld

Click to expand...

I totally disagree with "you are more likely to screw up using a lathe" statement.

I've done 'em many ways and now have my own repair lathe as a hobby. I can do a lot cleaner and faster tip replacement on the lathe.