AzBilliards Forums
The A to Z of Billiards Online
AzBilliards Forums
Home
Forums
New posts
Forum list
Trending
Search forums
Media
New media
New comments
Search media
Sportsbook
New events
Upcoming
Upcoming events
Upcoming bets
Member bets
Search
Members
Registered members
Current visitors
New profile posts
Search profile posts
Marketplace
Log in
Register
What's new
Search
Search
Search titles only
By:
New media
New comments
Search media
Menu
Log in
Register
Install the app
Install
Home
Media
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Media added by conetip
Navigation
Navigation
Browse albums
Prev
1
2
3
4
5
Next
First
Prev
2 of 5
Go to page
Go
Next
Last
Filters
Show only:
Loading…
With Angular contact bearing, shortened front seal cap.
conetip
Jun 22, 2014
0
0
Replaced Timken bearing with Angular contact bearing. Spacer is added at the back due to the shorter Front bearing.
conetip
Jun 22, 2014
0
0
J100 Handle
conetip
Jun 18, 2014
0
0
J100 Jumpcue
conetip
Jun 18, 2014
0
0
J100 handle logo
conetip
Jun 18, 2014
0
0
Finished with pulley
conetip
Jun 6, 2014
0
0
finished pulley attached
conetip
Jun 6, 2014
0
0
P1030451
conetip
Jun 5, 2014
0
0
P1030459
conetip
Jun 5, 2014
0
0
Spindle assembly, still needs the drive pulley.
conetip
Jun 4, 2014
0
0
Finished with cyano, Phenolic Ferrule with a Jump tip added.
conetip
Apr 16, 2014
0
0
Black Phenolic Ferrule and a Phenolic Jump Tip, Clean up tape removed.
conetip
Apr 16, 2014
0
0
Jeff's pooldawg tip trimmed
conetip
Feb 20, 2014
0
0
Turcite-vee-block , Milk Dud Tip by Jeff after trimming.
conetip
Feb 19, 2014
0
0
Turcite Vee support for tip trimmer
conetip
Feb 19, 2014
0
0
Threader
conetip
Jan 21, 2014
0
0
Finished tip trimmed, and polished the outside with some 600 grit paper. This is a snooker tip and is Ø9.55 mm
conetip
Jan 17, 2014
0
0
Trimmed front radius and moved around to the radial diameter stop, ready for the continuation of the pass.
conetip
Jan 17, 2014
0
0
Set up tip on mandre, Tip radius and diameter stop have already been set on a set up piece.
conetip
Jan 17, 2014
0
0
Assembled unit with router and 8 wing cutter, set to penny radius.
conetip
Jan 17, 2014
0
0
Cutting the 3mm wide slide through for the Router Clamp. Slitting saws if available makes for a quick and easy way of slitting these sort of things.
conetip
Jan 17, 2014
0
0
Using a block for support on the back jaw face. Drilling the M6 hole for clamping the router.I drill down with a 6.1mm drill just pass the slot mark.T
conetip
Jan 17, 2014
0
0
Flipped block over , leaving the same face against the vice jaw, so only need to find the hole center, in X (long axis). Y has not changed, C' bore to
conetip
Jan 17, 2014
0
0
Spot drill and drilling the capscrew holes. Drilled from under side, as that is the important side to match Taig Slide T slot.
conetip
Jan 17, 2014
0
0
Prev
1
2
3
4
5
Next
First
Prev
2 of 5
Go to page
Go
Next
Last
Home
Media
Top