Go Back   AzBilliards.com > Search Forums
Reload this Page Search Results
Showing results 1 to 11 of 11
Search took 0.00 seconds.
Search: Posts Made By: oldschool1478
Forum: Main Forum 02-26-2015, 08:39 AM
Replies: 777
Views: 405,102
Posted By oldschool1478
Nice tool! Looks like my table rating should be...

Nice tool!
Looks like my table rating should be revised:

Table Size = 9ft
Units = Inch
Pocket mouth size = 4.5
Pocket throat size = 3.875
Shelf depth = 1.5

Table Size Factor: 1.00
Forum: Main Forum 07-20-2013, 06:08 AM
Replies: 777
Views: 405,102
Posted By oldschool1478
Stardust Club (Manchaca, TX) - Brunswick Medalist...

Stardust Club (Manchaca, TX) - Brunswick Medalist

Good position over shelf. May be slightly off parallel with slate, but measurements should be within 1/16". The shelf radius is hard to see in...
Forum: Main Forum 07-13-2013, 10:24 AM
Replies: 777
Views: 405,102
Posted By oldschool1478
Due to revised chart (as I understand it) using...

Due to revised chart (as I understand it) using pocket angle of 141 deg.I have revised my table to:
oldschool1478 -- 9':1.00 -- 4 1/2":1.02 -- 5/8":1.00 -- 1 3/4:1.00 -- 1.02 (updated Red Badge...
Forum: Main Forum 07-08-2013, 05:28 PM
Replies: 777
Views: 405,102
Posted By oldschool1478
I guess you could call mine.. Updated Red Badge...

I guess you could call mine..
Updated Red Badge Diamond Pro


Dan
Forum: Main Forum 07-08-2013, 11:12 AM
Replies: 777
Views: 405,102
Posted By oldschool1478
rexus31 pockets The shelf radius is a bit...

rexus31 pockets

The shelf radius is a bit hard to see, but I think I have it about right.

Dan
Forum: Main Forum 07-08-2013, 05:44 AM
Replies: 777
Views: 405,102
Posted By oldschool1478
mamics pockets measured in Autocad. Dan

mamics pockets measured in Autocad.

Dan
Forum: Main Forum 07-02-2013, 01:05 PM
Replies: 777
Views: 405,102
Posted By oldschool1478
Sorry wrong photo! Dan

Sorry wrong photo!

Dan
Forum: Main Forum 07-02-2013, 01:00 PM
Replies: 777
Views: 405,102
Posted By oldschool1478
No promises but...... Here is SloMoHolic's...

No promises but......
Here is SloMoHolic's Pocket Photo.
Would be be more accurate if taken parallel to slate over shelf.
Forum: Main Forum 07-02-2013, 09:24 AM
Replies: 777
Views: 405,102
Posted By oldschool1478
I'd like to see that same shot with the cloth off...

I'd like to see that same shot with the cloth off the rails.
The mouth looks right. I have seen wedge shaped shims.
Forum: Main Forum 07-02-2013, 07:35 AM
Replies: 777
Views: 405,102
Posted By oldschool1478
It sounds like your pocket facings may have been...

It sounds like your pocket facings may have been shimmed. This often makes the facings too hard, and can deaden the bounce.
I cut my cushions on plane with the factory rail ends, and glued on a...
Forum: Main Forum 07-01-2013, 11:17 AM
Replies: 777
Views: 405,102
Posted By oldschool1478
My Diamond Pro

I modified the rails (per RKC specs) and installed Artemis cushions on my red labeled
Diamond Professional, bringing it up to the blue label specs. Cloth is Simonis 760.

50x100 = 1.00 TSF, 4 1/2...
Showing results 1 to 11 of 11

 
Forum Jump


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity (Lite) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.