Go Back   AzBilliards.com > Search Forums
Reload this Page Search Results
Page 1 of 40 1 2311 Last »
Showing results 1 to 25 of 1000
Search took 0.05 seconds.
Search: Posts Made By: Kim Bye
Forum: Main Forum Yesterday, 02:54 AM
Replies: 7
Views: 566
Posted By Kim Bye
It's a new shaft from Mezz, no carbon fibre core,...

It's a new shaft from Mezz, no carbon fibre core, all maple and with a ferrule similar to the deep impact break shaft. 12.5mm tip diameter and a very nice taper, similar to the Mezz all maple shaft.
Forum: Ask The Cuemaker 01-27-2020, 01:40 PM
Replies: 2
Views: 349
Posted By Kim Bye
Maybe you could tell us more what type of inlays...

Maybe you could tell us more what type of inlays you want and is your blank oversized and who made it?
You say it needs to fit a Uni-Loc Ignite shaft?
Ignite does not come in Uni Loc, so is the...
Forum: Main Forum 01-26-2020, 02:22 PM
Replies: 7
Views: 566
Posted By Kim Bye
Have you considered the new Sigma shaft from...

Have you considered the new Sigma shaft from Mezz. Great feel, nice taper and very low deflection :smile:
Forum: Ask The Cuemaker 01-23-2020, 08:44 AM
Replies: 7
Views: 332
Posted By Kim Bye
Why do you think it's a distinction between a...

Why do you think it's a distinction between a maple shaft and a LD shaft?
I make maple shafts, and they are low Deflection by any standards.
Forum: Ask The Cuemaker 01-20-2020, 01:15 PM
Replies: 5
Views: 362
Posted By Kim Bye
I live too far from you for that to be practical,...

I live too far from you for that to be practical, but any serious cue maker will be able to help you. If you just want to remove the pin, plug the cue and install a 3/8-10 pin, it's most likely...
Forum: Ask The Cuemaker 01-20-2020, 11:23 AM
Replies: 5
Views: 362
Posted By Kim Bye
Should be just fine. If you want to remove the...

Should be just fine. If you want to remove the ALU joint collar and replace it with Juma, phenolic etc you will need to pay for a partial refinish to.
Forum: Ask The Cuemaker 01-20-2020, 06:17 AM
Replies: 17
Views: 842
Posted By Kim Bye
The pumps are just a guide, you need a scale, so...

The pumps are just a guide, you need a scale, so you can mix the two parts accurately. Regular West is 1:5.
Forum: Ask The Cuemaker 01-19-2020, 11:37 AM
Replies: 17
Views: 842
Posted By Kim Bye
You can use the fast or slow hardner, it all...

You can use the fast or slow hardner, it all depends on your prefrences.
Forum: Ask The Cuemaker 01-17-2020, 02:35 PM
Replies: 2
Views: 443
Posted By Kim Bye
You can get burgundy with white spec.

You can get burgundy with white spec.
Forum: Ask The Cuemaker 01-15-2020, 01:50 PM
Replies: 4
Views: 515
Posted By Kim Bye
You can safely remove CA on CF shafts with...

You can safely remove CA on CF shafts with acetone.
Forum: Ask The Cuemaker 01-14-2020, 01:13 PM
Replies: 11
Views: 846
Posted By Kim Bye
Have you mounted it the wrong way?

Have you mounted it the wrong way?
Forum: Main Forum 01-13-2020, 06:36 PM
Replies: 10
Views: 425
Posted By Kim Bye
Of course a super soft tip will flatten over...

Of course a super soft tip will flatten over time. There is nothing wrong with the tip or installation.
Forum: Ask The Cuemaker 01-13-2020, 03:38 PM
Replies: 2
Views: 275
Posted By Kim Bye
You create backspin my friend. If it`s a kamui or...

You create backspin my friend. If it`s a kamui or Zan, Soft or hard, the difference is minimal.
Forum: Ask The Cuemaker 01-13-2020, 06:43 AM
Replies: 4
Views: 657
Posted By Kim Bye
Have a new wood piece made, much easier that way.

Have a new wood piece made, much easier that way.
Forum: Ask The Cuemaker 01-13-2020, 06:43 AM
Replies: 7
Views: 539
Posted By Kim Bye
Can you post some pictures in focus? A...

Can you post some pictures in focus?
A combination of a mid extension and butt extender would solve your problem
Forum: Ask The Cuemaker 01-08-2020, 11:41 AM
Replies: 7
Views: 555
Posted By Kim Bye
WD40 is a penetrating oil, wich means it creeps...

WD40 is a penetrating oil, wich means it creeps in everywhere, that's not a good thing for wood.
Forum: Ask The Cuemaker 01-07-2020, 08:04 PM
Replies: 10
Views: 796
Posted By Kim Bye
Tiger burnishing liquid.

Tiger burnishing liquid.
Forum: Ask The Cuemaker 01-07-2020, 08:01 PM
Replies: 7
Views: 555
Posted By Kim Bye
A vise with soft jaws and a big screwdriver. Heat...

A vise with soft jaws and a big screwdriver. Heat if that wont work. No wd40 ever!
Forum: Ask The Cuemaker 01-07-2020, 07:59 PM
Replies: 5
Views: 595
Posted By Kim Bye
Have you considered slicing the wood into pices...

Have you considered slicing the wood into pices and either glue it up i pies or cutting it up into strips with 45 degree edges and gluing it all to an octagonal core?
Forum: Ask The Cuemaker 01-07-2020, 07:52 PM
Replies: 5
Views: 498
Posted By Kim Bye
You can buy a 3/8-10 aluminum quick release pin. ...

You can buy a 3/8-10 aluminum quick release pin.
I would never do such a job though. Break/jump cues is a compromise. Spend the money on a separate jump cue.
Forum: Ask The Cuemaker 01-06-2020, 03:36 PM
Replies: 7
Views: 515
Posted By Kim Bye
Just make sure you drill and bore a starter hole,...

Just make sure you drill and bore a starter hole, 1" deep is enough, just enough to get the head of the gun drill to fit snugly in your blank.
Forum: Ask The Cuemaker 01-06-2020, 02:28 PM
Replies: 8
Views: 598
Posted By Kim Bye
Induction heater :smile:

Induction heater :smile:
Forum: Ask The Cuemaker 01-02-2020, 01:20 PM
Replies: 8
Views: 598
Posted By Kim Bye
No problem at all, I do work like that all the...

No problem at all, I do work like that all the time, as already mentioned, the shaft needs to be plugged and re-threaded.
Forum: Ask The Cuemaker 01-01-2020, 12:37 PM
Replies: 48
Views: 3,391
Posted By Kim Bye
Your overthinking things. The joint pin can be...

Your overthinking things. The joint pin can be used as a final means of getting just the right balance.
Some makers use G10, brass or SS exclusively, if it`s the "best" material or not can be...
Forum: Ask The Cuemaker 12-30-2019, 04:01 PM
Replies: 5
Views: 507
Posted By Kim Bye
I just use scraps from wrap installations.

I just use scraps from wrap installations.
Showing results 1 to 25 of 1000
Page 1 of 40 1 2311 Last »

 
Forum Jump


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity (Lite) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.