Go Back   AzBilliards.com > Search Forums
Reload this Page Search Results
Page 1 of 40 1 2311 Last »
Showing results 1 to 25 of 1000
Search took 0.06 seconds.
Search: Posts Made By: scdiveteam
Forum: Cue Machinery and Supplies 09-12-2020, 09:26 AM
Replies: 0
Views: 517
Posted By scdiveteam
Looking to buy large spool Irish linen

Hi,

Anyone have any Blue Mountain Large Spool linen they want to sell?

Rick
Forum: Ask The Cuemaker 09-09-2020, 02:54 PM
Replies: 36
Views: 2,235
Posted By scdiveteam
I use a Hardinge Collet chuck lathe with new...

I use a Hardinge Collet chuck lathe with new bearings that runs at Zero TRO. I bore slightly over the center barrel dia. After the epoxy is inserted I indicate the pin 1.1 inches from the face and...
Forum: Ask The Cuemaker 09-09-2020, 02:24 PM
Replies: 36
Views: 2,235
Posted By scdiveteam
A 10 to 25% volumetric shrinkage is not from...

A 10 to 25% volumetric shrinkage is not from wicking in to Juma PJ.
Forum: Ask The Cuemaker 09-06-2020, 12:26 PM
Replies: 36
Views: 2,235
Posted By scdiveteam
Wink Concerning shrinkage of coatings. Many cue...

Concerning shrinkage of coatings.

Many cue makers coat their cues one day, wait a day or two, sand then prep and spray clear coat. This is a problematic procedure. Why? All epoxies have a set...
Forum: Ask The Cuemaker 09-06-2020, 12:12 PM
Replies: 36
Views: 2,235
Posted By scdiveteam
Wink Concerning shrinkage of coatings. Many cue...

Concerning shrinkage of coatings.

Many cue makers coat their cues one day, wait a day or two, sand then prep and spray clear coat. This is a problematic procedure. Why? All epoxies have a set...
Forum: Ask The Cuemaker 09-05-2020, 10:27 AM
Replies: 36
Views: 2,235
Posted By scdiveteam
Fyi, 105 206 goes on clear but yellows on...

Fyi,

105 206 goes on clear but yellows on white.
Forum: Ask The Cuemaker 09-04-2020, 05:19 PM
Replies: 36
Views: 2,235
Posted By scdiveteam
Exclamation Hi, You burned thru the coating thickness. ...

Hi,

You burned thru the coating thickness.

100 is too aggressive.

You need to know the exact thickness of your adhesion coat and also the finish coat as referenced to the finished joint...
Forum: Cue Machinery and Supplies 09-02-2020, 10:22 AM
Replies: 0
Views: 514
Posted By scdiveteam
Looking for Unique Big Bore Chuck from Cue Companion

Hi,

If you have a Unique Cue companion, only do tip work and don't use the big chuck. I need one and will purchase it.

Text me at 847 641 0276 for quick sale.

Rick
Forum: Ask The Cuemaker 07-19-2020, 04:58 AM
Replies: 4
Views: 757
Posted By scdiveteam
Unhappy Beau, I did not resolve the issue with the...

Beau,

I did not resolve the issue with the display. My display is now larger and to be honest, I have no idea how it stopped being so tiny.

When I load a program file it is normal size and I...
Forum: Ask The Cuemaker 07-17-2020, 04:47 PM
Replies: 4
Views: 757
Posted By scdiveteam
Mach 3 Safe Z Question

Hi,

When I set and save my Safe Z parameters it works but I want my first move of the routine to raise the Z to .050.

Can anyone help me do that.

Thanks in advance,

Rick
Forum: Ask The Cuemaker 07-15-2020, 09:30 PM
Replies: 14
Views: 1,655
Posted By scdiveteam
Hi Kim, For years I had a problem with my...

Hi Kim,

For years I had a problem with my silver rings popping the finish a few months after I finished a cue. It was driving me mad and I stopped using silver or metal rings on my builds for...
Forum: Cue & Case Gallery 06-05-2020, 04:23 AM
Replies: 22
Views: 2,204
Posted By scdiveteam
Love Joel's designs

Love Joel's designs
Forum: Ask The Cuemaker 05-28-2020, 08:30 AM
Replies: 8
Views: 807
Posted By scdiveteam
Hi, I put a fiber pad on every tip I do...

Hi,

I put a fiber pad on every tip I do because over time if you take a face cut on the ferrule it gets smaller.

I never cut the pads off because it defeats my prime directive. If you face...
Forum: Ask The Cuemaker 05-20-2020, 08:10 AM
Replies: 1
Views: 627
Posted By scdiveteam
Elephant Ear Question????

Hi,

Is Elephant ear really from an elephant? I have always wondered.

Why is ivory illegal but Elephant ear ok?

When you consider the volume of material in one ear compared to cost per...
Forum: Ask The Cuemaker 05-19-2020, 06:57 PM
Replies: 35
Views: 2,518
Posted By scdiveteam
Hi, My shop air pressure is 110 psi. When...

Hi,

My shop air pressure is 110 psi. When operating a gun drill it is volume that is more important.

For me, I open the globe valve about 1/3 and my rpm is 400. My feed velocity is about 2...
Forum: Ask The Cuemaker 05-18-2020, 07:55 AM
Replies: 3
Views: 699
Posted By scdiveteam
Mach 3 Display Table Question.

Hi,

I had some problems setting up my mach 3 because of some computer issues earlier this year. Back up and running for last 3 month and loving the reliability of everything working well.
...
Forum: Ask The Cuemaker 04-22-2020, 10:14 PM
Replies: 15
Views: 1,204
Posted By scdiveteam
Hi, I had this problem years ago. Dont...

Hi,

I had this problem years ago.

Dont use a sharp carbide tool. I had a carbide tool and kept it sharp with a green wheel. Great for turning but causes finish lifting when facing after...
Forum: Ask The Cuemaker 03-14-2020, 10:53 PM
Replies: 65
Views: 3,112
Posted By scdiveteam
Talking Hi I build my cues on a 30" laminated maple...

Hi

I build my cues on a 30" laminated maple dowel.

When I broke form the A Joint method here is some of reasons why I prefer my full core method. Nothing bad to say about A Joint method but...
Forum: Ask The Cuemaker 03-05-2020, 09:01 AM
Replies: 10
Views: 787
Posted By scdiveteam
45 % humidity and 59 to 70 degrees is the correct...

45 % humidity and 59 to 70 degrees is the correct controlled invironment. JMO
Forum: Ask The Cuemaker 01-07-2020, 01:11 AM
Replies: 40
Views: 3,305
Posted By scdiveteam
Hi, On oily woods, apply liberal amounts of...

Hi,

On oily woods, apply liberal amounts of acetone to pull the oil from the outer area of the substrate.

When the paper towel stops showing bleed, let the cue come to room temp. Then apply...
Forum: Ask The Cuemaker 12-12-2019, 09:21 PM
Replies: 17
Views: 1,485
Posted By scdiveteam
After all is said and done, I am back up and...

After all is said and done, I am back up and running very well.

Turns out that 388 was not the address that worked for me.

I had a new computer custom built for me 2 years ago and bought a new...
Forum: Ask The Cuemaker 11-30-2019, 04:20 PM
Replies: 17
Views: 1,485
Posted By scdiveteam
Thanks to those who tried to help. I had the...

Thanks to those who tried to help. I had the right address all along as verified by Kim and Al.

Turns out my device manager does not see my LPT port only a com port. Rut Roe Scooby!

Kim took...
Forum: Ask The Cuemaker 11-30-2019, 05:35 AM
Replies: 17
Views: 1,485
Posted By scdiveteam
Thanks Alan, I will try that. Rick

Thanks Alan,

I will try that.

Rick
Forum: Ask The Cuemaker 11-29-2019, 05:07 PM
Replies: 17
Views: 1,485
Posted By scdiveteam
Mach 3 XP Com Port Address Question

Hi,

Reinstalled my licenced Mach 3 with new XP System on my computer.

Is anyone running Mach 3 with XP that can tell me the Com Port address for Com 1 in Pins and Ports.

I have the old...
Forum: Ask The Cuemaker 07-20-2019, 12:37 PM
Replies: 12
Views: 1,696
Posted By scdiveteam
Good points Kim. I don't stain too often,...

Good points Kim.

I don't stain too often, when I do I use this procedure.

I always use kiln dried wood only. Always.

After 320 sanding, I like to use acetone on the surface.several times,...
Showing results 1 to 25 of 1000
Page 1 of 40 1 2311 Last »

 
Forum Jump


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity (Lite) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.