Search results

Anyone know who makes some of the collapsible ball racks that are occasionally seen at tournaments, league nights, etc? Google search didn't bring up anything.

Kudos to Diamond Billiard Products (Greg Sullivan) and On The Wire Creative Media (Ra Hanna) for putting together this Junior Event. I was chagrined when the DCC moved to an exclusive 21-and-over venue, so this is a great effort to keep the juniors competing and improving. If you know a junior...

I have used the Simonis video technique to install Simonis cloth on my Diamond table and it worked well. Does anyone know if I can use the same technique to install Mercury Ultra cloth on the bed of an Olhausen table, or should I just use the traditional installation technique? Thanks.

I own a few Diveney sneaky pete cues and I love the soft hit. I'd like to have him build me a couple new shafts but for a Jacoby butt I own, but Pat will not do it. I'm going to have to go through a local cue builder. Does anyone know if Pat uses any special techniques (drilling out the core...

I recently purchased a 35+ year-old Valley Barbox for which I bought new Valley cushions from Seyberts. The table played well for a year, but over the last 2 months I've been getting ball acceleration off some of the rails. Now, if I hit a ball medium speed at a rail (not jumping the cueball)...

I ordered some DVDs from Corey's website: http://schoolofpool.com/ I ordered a few weeks ago and haven't heard anything - no order status, shipping, etc. Emailing them has not helped. There is no phone number to contact them. Have any of you ordered from his site and actually received the...

I will be in the area in early January (a couple of miles north of Old Town). Any recs on a place to bang a few balls? I'd settle for a barbox if its close by. Thanks.

What is the best way to get a break tip flush with the ferrule on a lathe? I am installing a White Diamond Ultra tip. With a typical leather tip, I usually take the edge down close with the cutting tool, then use a utility blade parallel with the ferrule to trim it flush. The issue is that...

Are there any special considerations when replacing a tip on a cynergy shaft, or is it just a standard job? Fiber pads? Anything unique about the ferrule? Thanks in advance.

I used bondo to seal the seams on my diamond a few years ago (worked beautifully). I am going to be moving the table soon - is it difficult to remove the old bondo? Any suggestions on how to do so - a certain grit sandpaper? Chemicals? Just trying to be prepared. Thanks.

...........

Does anyone know if it is possible to purchase a BCA membership in order to qualify for the Tourney next month? I don't have a BCA league near me. Thx.

I'm looking for the set of used DVDs. Please PM me. Thanks.

I don't have experience with 314-3 shafts, but I am removing a Kamui tip with the clear backing. After removing the tip, the middle surface is gray, which is not what I was expecting (white). It looks as though its not a capped ferrule, but from what I understand all Predator ferrules are...

Looking for a bar with 7 foot tables in Hendersonville, nothing fancy. Will be there for one night. A quick AZB search suggested Fat Cats, but that is a little too far outside of town. Thanks.

I have a new Jacoby sneaky pete butt that is a little big for my predator shaft (wood-wood Uniloc joint). The butt diameter at the joint is 0.850 inches and the shaft is 0.840. It would be nice to not have the little lip at the joint. Is there any way the butt could be trimmed down to match...

I have a custom cue made by a local cuemaker which has a Uni-loc joint (not radial). I use a predator shaft with it and had no problems for about six months. Over the last few weeks I have noticed the last turn to screw the cue together is very tight. I almost have to muscle it to get it to...

I was trying to order a custom sneaky pete from Jacoby. I used their online system to get a quote - no response after 2 months. I then called them and requested a quote. I got the receptionist's email address and emailed her the specs. No response after 2 weeks. I emailed her again. No...

If I play in the DCC 9 ball do I get free reign to watch the finals or do I have to pay more? Thanks.

I just got a Schmelke cue, its great but its about 15oz. Is it difficult to add a weight bolt? I'd like the cue to be about 19oz.