Search results

Dang, got asked to cut a house cue, had a ring middle way. I told the owner it likely had a bolt there, it did. I cut it fine. I drilled it and bored it, almost done and boring bar sent last 1/16 threw the side of the butt. What did I do wrong? I ran a 1/4 end mill, then the boring bar.

My motor controller died on my mid america lathe. I bought another resistor and replaced the bad one and it burnt back out again. I talked to Todd and he told me what a new one costs. My question, my old one did last 9 years, but is there something better I should buy or just get another like I had?

Guys help me out, I have a shaft nearly finished on an old conversion sneaky, one I took the finish off of and am ready to apply finish to the shaft and the butt. The problem I am seeing is the shaft is way too white for it to look good to me. Is there a way to yellow the maple shaft some, maybe...

All 10, SOLD shipped, first post gets first chance, I'll PM you. I forgot to mention, I would be willing to trade for some equipment.

30 bucks shipped, first post gets it, I'll PM you if you are first.

I think I will like this much better than the scroll chuck.

I have the half nut assembly from an atlas th54 I would like to sell. I has the ball, spring, both half nuts, and handle. I think these are the part numbers : 9-13,10D-38,10-29,9-61,9-210 & 9-62 x 2. I would like SOLD if anyone can use it but am up for best offer.

Presents for niece and nephew. I am not good a taking pictures, the coco really had a lot of figure. oh well.

I got tired of trying to mask the bottom of the shaft and the top of the butt when shooting auto clear so I made these little delrin spacers on the last 5 that I cleared and they worked great. Just wondering if anyone else does anything like this?

A few almost ready to finish.

I am looking for a boring bar to do my pins with. I'm guessing I need something around 1/4 by about 2.5 inches bore depth. Not having much luck after looking for a while. Does anyone have anything like this that they would want to sell or any recommendations?

I have the following Chris Hightower DVDs I would like to sell. 1. Advanced Cue Building : Points and Inlays 2. Advanced Cue Building : Cue Assembly, Boring, Coring, Tenons and more. 3. Basic Cue Building: Includes tips, ferrules, reconditioning, shafts,wraps,tapering, joint work and more 4...

I can't seem to find a solid brown Irish Linen. I need a dark brown similar to the walnut brown at Atlas. I don't care if you only have large or small roll, I just need enough to do 1 cue but will buy more if needed. I have checked atlas, prather, schmelke, mueller, and a couple google searches...

Got a question, I am about to core some forearms and I have the 5/8 drill and 3/4 drill. Which would you use and why? The main reason I don't want to use the 5/8 is because I usually open up the joint collars a little and haven't got the best idea how to overcome this. Should I make my coring...

I need a piece big enough to make a butt cap out of that matches this picture. It is the top piece of wood below.

After doing a little bit of time killing reading on Taigs' website, does anyone fill their bed with concrete as Taig suggest to do? Would there be any real benefit. I have a couple that are not just hadn't really thought about it.

All Items sold.

I have a piece of Amboyna Burl a little over 1.5 square and a little over 15.5 inches. SOLD

Looking for a 4 jaw independent chuck, used hopefully, just need it for one job so I thought maybe someone has one laying they would like to sell before I buy a new one.

I have used 5 minute epoxy before and waited until it setup some before pushing it on to prevent the expoxy from soaking in and leaving a dark line behind the ferrule. I have also heard people say 5 minute epoxy has no business being used for ferrules even though I have never had one pop using...