Recent content by fat tony

I appreciate all your comments and advice. The soup can method isn't applicable here, because my slate isn't broken all the way through. Only a 1/8" thin top layer of the slate has broken off at some point, glued back in, and now sits a bit proud of the rest of the slate. Check the pics I...

Thanks for the reply and suggestions! The tape method might not be sufficient because the tolerances are quite tight as it is. I don't want the sanding block to be riding on anything else than the reference surface, meaning the rest of the slate which defines the 'zero'. The sanding paper...

I need to fix a broken slate, and could use advice as to how to go about it. The pictures show how it's broken; a 5x5x5" about 1/8" thin triangular piece of the slate surface has broken off at some point. It has been glued back on, and now sits a bit proud compared to the rest of the slate. I...

I did nothing on purpose, I couldn't even tell which 2 rails were cut from the end of the cloth. Maybe next time I take pics nearer the ends of the rail and we'll see :)

ok I took the pictures today. 4 rails have cloth cut from the width of the bed cloth, and 2 rails are cut from the end of the (same) bed cloth. Can you tell which ones are which? Lighting conditions vary a bit, and no 2 picture is a still from a video clip since I fumbled with mah fat fingers...

I like it when some commenters first say how it doesn't matter whats between your legs....and then go on telling us about all those things that were supposed to be a non-issue. "We need more women on the tour". If gender isn't an issue, why? It's like saying we need more people on the tour who...

Thanks for the suggestion Sheldon. I think I'll put the new rail cloth + featherstrip in place when the corner castings are mounted, that way the casting is giving support to the glued featherstrip and cloth while it dries out. If the rail frame is rigid enough that it can be flipped over in...

Speaking of feather strips, how would you guys go about installing cloth around this beauty? Introducing the Riley Ray 9ft pool table corner pocket feather strip. The corner casting is supposed to tighten against the feather strip, keeping the rail cloth in place. A local bar asked me to repair...

Hi Ricky, I get the impression that even if you knew the cushion type you needed, you might not be experienced enough to take on five 9 footers at a pool hall with only 8 hours to spend on each, especially considering you need to change the cushions. And I seriously mean no disrespect. I'm a...

I don't :) I'll post pics as soon as this flu goes away and I get to go to the club.

I just might take pics of all the rails and you guys can guess which ones were cut from the end cloth :) Once at a wedding we got to drinking beer from glass bottles and cans. Of course I swore that the taste was metallic if from a can, so the lads poured beer to 3 cups from cans, and 3 cups...

Thanks for the reply and info Sheldon, I cut two rails from the side and four from the end. I just thought that there was a reason for "no rails off the ends" because of the weave of the cloth. I remember RKC saying that when trimming the rail cloth excess with a knife (like in one continuous...

Is it ok to cut rail cloth from the end of the cloth? Simonis documentation says "no rails off the ends" and shows a picture how the cloth is cut from 78" wide cloth and rails are cut from the width of the cloth. The billiards shop sent me 66" wide cloth for a 9' table. Should I send the cloth...

I see what you mean. The 140 degree pocket jig that was lined up with the (bolted down and cross-measured) rail frame with a carpenter's square gave those cuts, so I could not really question them. Edit: looking at it more closely, the left hand side corner piece is overlapping the rail wood...

Weird, or pure genius. There's a fine line you know :) Kidding aside, in the picture the corner pocket angles look too parallel, like the pocket doesn't open at all. IRL it does, and I'm chalking that down to the camera. It somehow does not give, well, a full picture if you like.