Recent content by sk8ordie

  1. sk8ordie

    Old Viking tenon ??

    That's exactly what I told this customer because the ferrule was also cut shorter than normal, about 1/2 inch. Imagine the guy who did this and thought you cut the ferrule short to lose weight for low end mass and then added a steel tack to hold it [emoji3] Sent from my SM-N986U using Tapatalk
  2. sk8ordie

    Old Viking tenon ??

    Had a gentleman bring by an older early window cue Viking for a tip change and noticed his ferrule was loose. It came completely off and this is what I found. Looks like someone tried to nail a ferrule on unless this was from factory. I know old Vikings had a medal threaded tenon but not this...
  3. sk8ordie

    Joss West value

    I hope this is the place to ask this but, I did some repairs on a local gentlemans cue's and he told me about this Josswest he had and he was selling and I was wondering if what he was asking was too much or in the ballpark. Thank you for any info. Sent from my SM-N986U using Tapatalk
  4. sk8ordie

    Brunswick medalist help

    Well, they did the floors today and the table lifted perfectly with no issues. Thank gawd I didn't have to take it apart. Thanks for your help guys!!! Sent from my SM-N986U using Tapatalk
  5. sk8ordie

    Brunswick medalist help

    That's exactly what I was going to try. Sent from my SM-N986U using Tapatalk
  6. sk8ordie

    Brunswick medalist help

    If the seams pop I would be okay with that I just want to make sure that I won't break none of the wood beams or actually break the slate. I would go very slow with the bottle jack and I only need it to lift up about an inch and a half, maybe 2. Sent from my SM-N986U using Tapatalk
  7. sk8ordie

    Brunswick medalist help

    So I'm going to have to take the whole table apart? Sent from my SM-N986U using Tapatalk
  8. sk8ordie

    Brunswick medalist help

    I was looking for someone who has done this like you have without issue. This helps alot. I will lift from the middle like you did. I want to make sure I won't break the 2x6 boards holding the slate. I can't have anything under or near the feet so the floor guys can get under the legs. Sent...
  9. sk8ordie

    Brunswick medalist help

    Need help and have a question about slightly lifting up my three-piece slate 9 foot Brunswick medalist. When my house was built they talked me into putting down vinyl roll flooring and it was done horribly. They are coming in in 2 weeks and putting a floating floor on top now. My question is, so...
  10. sk8ordie

    11.8 Cynergy CF shaft -Radial-

    Used (9.7 out of 10) for a month on and off. 11.8mm, 4oz 29" Cuetec Cynergy CF radial shaft. Tried 4 different CF shafts and they're just not for me. HOW med tip. Only trades considered are Predator Z3 Radial in perfect condition or 9.7 out of 10. $300 shipped within the USA only Sent from...
  11. sk8ordie

    Cuetec Cynergy 11.8 CF radial

    $275 split shipping Sent from my iPad using Tapatalk
  12. sk8ordie

    Cuetec Cynergy 11.8 CF radial

    Bump…….. Sent from my iPad using Tapatalk
  13. sk8ordie

    Cuetec Cynergy 11.8 CF radial

    Used (9.7 out of 10) for a month on and off. 11.8mm, 4oz Cuetec Cynergy CF radial shaft. Tried 4 different CF shafts and they're just not for me. HOW med tip. Only trades considered are Predator Z3 Radial in perfect condition or 9.7 out of 10. $300 shipped USA ONLY Sent from my SM-N986U...
  14. sk8ordie

    SVB vs Chang Update Thread

    Thanks for the updates!!!! Sent from my SM-N986U using Tapatalk
  15. sk8ordie

    SVB vs Chang Update Thread

    THANK YOU [emoji4] Sent from my SM-N986U using Tapatalk
Top