Search results

Bump and lower price. $380 shipped.

I wanted to try out several different ones to see if there really is a difference between the inexpensive, medium expensive, and super expensive carbon fiber shafts. I did the same thing with a few Kielwood shafts. I've started making my own CF shafts and "Kielwood" shafts and wanted to have a...

Responded to all PM's so far, thanks for the interest

I have a Revo that I bought for demo purposes. Chalked and test hit by me but have seen under 25 balls hit. 30", 12.4mm, Uniloc, and comes with the original case and wipes that Revo sends with these shafts new. I bought both of these new from Seyberts. $380 shipped, F&F

If your'e interested, I have a 30", 12.4 Radial, chalked and test hit only. Bought new from Seyberts to demo on one of my butts. Never been played. Mint condition with the case, wipes, and patch that comes with them new. $425 shipped CONUS.

I've had good luck with these: https://www.rockler.com/eye-candy-multipurpose-mica-pigment-additive-50g

As the OP, I would suggest that you re-read my post. I would like to play in more tournaments but many require established Fargo ratings in order to be allowed to play. I have no issues with the cost or time, as you suggest to "earn" a fargo rating. I have joined a league that reports to...

Why would this have ever left the Meucci factory unfinished ??

Every time, a stunner! Best in class Bob!

Good luck with that.. most likely the coating has soaked into the linen and in the gaps between as well. My guess it you tear it all off, sand and rewrap..

I had three sets of 860HR on hand, all in TB, 9', that I sold for cost but acquired 12-18 months ago, no problem.

I've just had an epiphany! For the shop I'm just finishing, I just assumed my makeup air for exhaust would come from outside and challenge my HVAC system (dedicated to the shop) to keep up. So I made the shop its own loop. I felt that the wild temperature and humidity variations of the...

Mine does a great job. The cyclone catches all of the big stuff and the pleated filter catches the small stuff. The cleaning mechanism for the pleated filter works well and the fines end up in the bag under the pleated filter. After using it for a full year, and then moving to a new house...

Full face 3M Dual Cartridge. When I started turning Cocobolo, I started getting some nasty rashes. From then on, when workign with exotic woods, I make sure I have no exposed skin. Full headgear, earmuffs, goggles, gloves, etc.

Thought so. New Gambler-2 looks the same but with the old shafts, hard to tell. Any idea what tip came on these cues 10 years ago? I don't know if I'll chalk one of these up or not..

With the archives down, it is harder to ID a cue these days. Can someone help me identify this Meucci I just bought? It is unplayed, came with two black dot shafts and one red dot shaft, all never chalked or played. I'm told it is 10+ years old but I haven't been able to confirm. Condition...

That's valid. I'm in the middle of configuring a new shop so perhaps I should rethink the collector location. I do run the air filtration system 100% of the time I'm in the shop and for 12 hours after I leave it which turns to air over every 3-4 minutes. I only run the chip separator and Hepa...

No doubt that some stuff gets through. That's why I also wear a respirator. You can only do so much.

No, I'm in the middle of a move, but here are links to the two units that I use.. https://www.rockler.com/dust-right-wall-mount-hepa-cyclone-dust-collector-1250-cfm?sid=V91158&gad_source=5&gclid=EAIaIQobChMIiO_-ja7EhAMVeZxaBR2HMQ89EAAYASAAEgLhdPD_BwE...

Makeup air is definitely an issue with external exhaust in a climate where outside temperature and humidity are quite variable. Living in Florida, temp swings are significant and humidity as well. My shop has its own dedicated HVAC unit with dehumidifier. However, my shop is also quite small...