Search results

I've used the original Tom M version of this pin for years on all my jump cues. The aluminum pin into a phenolic insert is more secure and lighter than using a Uniloc joint while still being quick to assemble.

Kielwood is a great choice for 1P. IMO no shaft connects you to the cue ball like KW. The feedback is great. I made a couple shafts for friend's McWorter and he loves them. He's a strong 1P player. I've made 31 inch shafts for a 6'6" customer. It had a 12.6 mm tip. It went with the 31 inch butt...

If you download the free Thread Pitch app, you simply compare your pin to image in the app (not my screenshot) and you'll know. Comes in handy when you left your thread gauge at home and someone asks if his pin is 10 or 11 TPI.

You've gotten a lot of good advice, I'll try not to repeat any advice. Have you measured the 150 RPM turn rate? Do you back off the spur collar for EVERY new blank that you put up and only position the spur AFTER after the dead center seats and the tailstock pressure is set? If the spur...

I love the smell of bocote shavings! I have a spreadsheet to calculate the effect of hogging out a cue. I don't use it much after getting Kelly's (far superior) CueBalance program. You should have patented your cue lengthening idea. .

John brought his cue by a couple weeks ago. It was a simple one piece bacote with a thick bumper held in with a screw. I had a 0.650 in. ribbed replacement bumper. The original bumper and screw was 0.2 heavier than the replacement bumper so it only needed to shed 0.43 oz. I bored a 5/8 x 1 inch...

If there are no metal rings, an inductive heater will make short work of it.

They both have nice textures. The Scotch texture is more uniform than the Spanish bull. If you like a glove soft feel, get the oil tanned Spanish Bull. The synthetic faux leather is great UNTIL it starts to outgas, soften and become gummy. It then starts to leave marks on your felt and clothing...

If it's the same size as the ones used on the cross slide, they are sold lots of places. Search for these: Square Nut: #10-32 Thread Size, Steel, 1/8 in Height, 3/8 in wide

You can quickly check the alignment by putting a dead center in the tailstock chuck and another dead center in the headstock chuck. Move the centers together to pinch a utility blade between them. If the centers are aligned, the utility blade will be suspended vertically and will be...

I can't see why adjusting the internal pots would cause a premature failure. When they failed, did you: Replace them as a pair? Add thermal compound between the part and the mounting surface? Buy the parts from a reputable US supplier?

Remove the tip. If the ferrule is capped, trim it down until the top of the tenon shows. With your lathe in reverse, use a thick piece of leather to pinch down on the ferrule. Be careful as the ferrule is going to get very hot. Thermoset ferrules may begin to deform. The intention is to...

DId you check the power MOSFET? I believe the MOSFET part is 1RFP460?

3M NRR 30 dB muffs. I have a Bose noise canceling set but the 3M is my go to.

Carom and pool utilize different strokes. Pool has a longer bridge length and a long smooth stroke. Side English is applied judiciously. Carom uses a shorter bridge and often employ a quick punchy stroke. Many carom shots require extreme side spin. Carom cues are shorter and more stout. The...

For $5, they’re a good value. However, not one top player has ever asked me to install an US tip on their cue. I once asked the late Royce Bunnell (OB Cues) what he thought the most important part of a cue was. Without hesitation, he said the tip was easily the most important cue component...

Based upon your information, your Y axis zero in Mach 3 is not correctly set to the center of rotation. If it was, you would be cutting into the shaft and the cutter would have likely crashed into the steel adapter damaging your cutter. You can quickly check this for yourself. Remove the shaft...

If X is your long axis (12.5 inch direction) and Y is your 'depth of cut', you need to zero the Y axis at the center of rotatation (interchange for Y is long axis). Sounds like it's zeroed on the dowel edge.

"Torrefication" is not a word. Wood that been subjected to the torrefaction process becomes torrefied. I also used term "torrefication" before discovering that it wasn't a real word. Turning/sanding torrefied maple reminds me of toasted marshmallows.

Get the rod and reel. You'll catch more fish.