New small tool for my shop

A mini lathe to do tips with

Small box but well wrapped ...
 

Attachments

  • 6tiptool.jpg
    6tiptool.jpg
    46.2 KB · Views: 290
mini lathe close up

Pic a little unclear, might be that I was a little to excited :)
 

Attachments

  • 7tiptool3.jpg
    7tiptool3.jpg
    44.7 KB · Views: 290
Cross slide was knocked in tho the box

on the mini lathe... Hope it did not take any damage..
 

Attachments

  • 66crossfeed.jpg
    66crossfeed.jpg
    26 KB · Views: 291
DRO packed on the lathe

Was wondering what this package was but quickly found out.
SINO DROs is used.
 

Attachments

  • 8DROpack.jpg
    8DROpack.jpg
    53.9 KB · Views: 287
DRO setup in the back of the bed

I guess not to easy to see, but...
 

Attachments

  • 11DRO_setup.jpg
    11DRO_setup.jpg
    41.7 KB · Views: 295
Chuck

"peanut butter" is applied and some kind of paper to keep it there..
Normal 3jaw version.
 

Attachments

  • 9chuck_packed.jpg
    9chuck_packed.jpg
    35 KB · Views: 248
Controls

Hope to do US threads without to much mucking around with cogwheels
where hopefully some of these buttons could help me:)
 

Attachments

  • 10control.jpg
    10control.jpg
    48.8 KB · Views: 242
Main axle

Back plate is solid casted aluminum and I guess I have to mill a larger hole here
to fit one of Chris back chuck.. I'll have to do some measurements first..
 

Attachments

  • 12mainaxle.jpg
    12mainaxle.jpg
    14.8 KB · Views: 242
Cover taken off

Belt drive arrangement. Curious about the noise level...
 

Attachments

  • 13mainaxle2.jpg
    13mainaxle2.jpg
    37.9 KB · Views: 240
QCT turret.

I ended up with the "german" version I "reviewed" up here earlier..

Lots of "peanutbutter"
 

Attachments

  • 15QTturret2.jpg
    15QTturret2.jpg
    40.5 KB · Views: 233
Tools supplied

Left box included the original tool holder and 3 more tool holders.
Center was normal Chinese junk tools and additional cogwheels and live senter
Right = 4 jaw independent chuck
 

Attachments

  • 16tools2.jpg
    16tools2.jpg
    41.5 KB · Views: 237
motor

Looks pretty big to me... 3 phase setup so I need to get one of those wise
guys to come and hook it up..
 

Attachments

  • 17motor.jpg
    17motor.jpg
    33.5 KB · Views: 236
Tool box and manual,certificate etc

Certificate seems to be the typical Chinese way of doing things:
Copy of some type of machine (handwritten numbers is not done "by hand"
but seems to be a blue print of a previous manual) where some "quality"
man has put a Chinese stamp in there...
Not sure if this means that the machine meets the "numbers" in there or
is better, but I guess it would be accurate enough for me.
I hope at least :scratchhead:

I'm not going to bore you with more pics now for while... Hopefully next
would be of a cue :)

Thanks to those who have guided me in this "quest" and all my questions..
T.I.R?,weight on lathes?,length on lathes? and well, I guess I have asked a lot.

K
 

Attachments

  • 18tools.jpg
    18tools.jpg
    42.9 KB · Views: 233
You must log in or register to reply here.
Back
Top