Wood Polisher on a custom cue
- Thread starter Marc
- Start date
If it really needs refinishing, send it to a pro. Why risk it?
I use renaissance wax. It says it's for furniture
If the British Museum and restoration specialists internationally use Renaissance Wax to revive and protect furniture,
art frames, ivory, etc., it should be ideally suited for use on pool cues, much more so than other commercial products.
art frames, ivory, etc., it should be ideally suited for use on pool cues, much more so than other commercial products.
Did he say it needs refinishing?
IMHO, several high grade wax finishes are suitable.
That is a high grade wax suitable for fine finishes on valuable pieces.
I have seen you post this before and honestly think it deserves more attention.
Any cue finish should benefit from a protective wax coating. More modern coatings are ceramic. There is controversy about using such a thing on a shaft, but likely it can work well on a butt. I would be careful with a truly valuable cue though.
I would recommend contacting a cue maker for their recommendation of the care and preservation of their work if they are still around.
For really high grade cues, meaning those that are extremely valuable, nothing on it would be my first answer. If they are on display they should be behind glass with UV coating or plexi with UV protection.
The best of the best cues with original finish need to be considered carefully for preservation. Don't do anything that could react with the original finish. Generally speaking high grade waxes are excellent, and can be stripped and reapplied if needed without toughing the underlying original finish.
I think one needs to consider whether the cue is in use, on display, or in storage as well when one considers whether or not to put anything at all on it.
Most of my cues just get wiped off. A few get wax. I haven't tried any synthetic or ceramic coatings at all and am hesitant to do so.
My joss? That just has decades of hands on use and occasional wipe down. But it certainly isn't a "high grade" valuable cue. It's a player.
billiards_watch
Well-known member
They're good cues.
High grade doesn't normally mean good.
There is a reason the question, "How does it hit?" comes up. Its usually reserved for "high end" cues.
Ok sorry I will stay in my lane bro!
I periodically apply a light coat of Renaissance Wax to my cue shafts after wiping the shafts with a damp cloth or a cloth towel moistened with rubbing alcohol. The wax really leaves a glossy smooth finish that creates a coating. It seals the wood pores opened by cleaning the shaft. It is important to apply at least 2 coats after cleaning the shaft otherwise a single coat of Renaissance wax regularly applied keeps your shafts like satin. I’ve been doing this for years with all my cues and for friends. Before Renaissance Wax, I was using Craftsman Cue Wax (Birmingham, England) but it’s hard and expensive to obtain.
Last edited:
Biloxi Boy
Man With A Golden Arm
Not a very scientific analysis, but whenever I am watching videos of cue makers at their benches, I make it a habit to check out what products and tools they have readily at hand. Often I see a can of Renaissance Wax.
Last edited:
I use Chem-Pak Q Wax:
www.pooldawg.com
Any thoughts on whether that is okay? Who is a legitimate source for Renaissance Wax?
Chem Pak Q Wax Pool Cue Wax
The original Q Wax is specially formulated with the finest carnauba wax to give your cue the ultimate in protection. Use Q Wax on a regular basis to help preserve the natural characteristics of the wood.
www.pooldawg.com
Any thoughts on whether that is okay? Who is a legitimate source for Renaissance Wax?
AZ'RS!!!!!
Most CUSTOM CUES Have AUTOMOTIVE CLEAR COAT FINISH-
SO....Use automotive car wax, NOT FURNITURE POLISH-
Probably wont hurt the finish, BUT I still recommend even Turtle wax for your cue...
SOME Custom cues have BEEN FINISHED WITH CA=Super Glue finish-
I recommend-go to the forum ASK THE CUEMAKER- Here on AZ-
Ask, who uses CA TO CLEARCOAT their cues-
WHAT POLISH OR WAX RECOMMENDED????
billiards_watch
Well-known member
You guys putting wax on your shafts better make sure the wax has no color.
I experimented with car wax and made the mistake of putting Turtle Wax on my shaft and it gave it a hint of green. The green goes away but you don't want that. Thankfully, it was on a cheap ass cue.
I experimented with car wax and made the mistake of putting Turtle Wax on my shaft and it gave it a hint of green. The green goes away but you don't want that. Thankfully, it was on a cheap ass cue.
The wax won't create stickyness, or does it do the opposite..?