WTB maintenance arbor 3/8-14

[steev]

Like the title says, I need a maintenance set for 3/8-14.

My Omega/DPK needs minor repair work and my local guy doesn't have the arbor to get it on the lathe. Last time I needed a tip, he tried using a 3/8x10, I barely caught him before damage was done...

-s

 

[cuemaker03]

Call Mike Bender

 

[chuckpilegis]

Do they use that size on a Cuetec?

 

[ArizonaPete]

Do they use that size on a Cuetec?

Yes, some Cuetec cues are 3/8x14.

 

[Dirtbmw20]

Like the title says, I need a maintenance set for 3/8-14.

My Omega/DPK needs minor repair work and my local guy doesn't have the arbor to get it on the lathe. Last time I needed a tip, he tried using a 3/8x10, I barely caught him before damage was done...

-s

http://www.ebay.com/itm/Cue-Lathe-D...360?pt=LH_DefaultDomain_0&hash=item27be250798

 

[GBCues]

There's also one listed here:

http://forums.azbilliards.com/showthread.php?t=283119

Gary

 

[KJ Cues]

Yes, some Cuetec cues are 3/8x14.

Let's nip this in the bud before the misinformation travels any further.
CueTec IS NOT 3/8x14. It's an oversize 9mm x 14.
There's about .020" difference.

KJ

 

[OneIron]

Let's nip this in the bud before the misinformation travels any further.
CueTec IS NOT 3/8x14. It's an oversize 9mm x 14.
There's about .020" difference.

KJ

Any idea where to get the right one?

 

[KJ Cues]

Are you asking where to get the CueTec tap or a 3/8x14 maintenance driver???
I sell the CueTec tap which is how I know what size they are.

KJ

 

[steev]

There's also one listed here:

http://forums.azbilliards.com/showthread.php?t=283119

Gary

Saw that yesterday, but I don't need all that stuff.

-s

 

[steev]

http://www.ebay.com/itm/Cue-Lathe-Dr...item27be250798

Thanks, this is what I needed :thumbup:

-s

 

[OneIron]

Are you asking where to get the CueTec tap or a 3/8x14 maintenance driver???
I sell the CueTec tap which is how I know what size they are.

KJ

Cue Tec maintenance set.

 

[KJ Cues]

http://www.ebay.com/itm/Cue-Lathe-Dr...item27be250798

According to the seller (Unique Products), this one will work for the CueTec also.
This is assuming the major dia. of the driver's pin is btwn. .354" & .360".
Any bigger than that and it won't fit the CueTec shaft.

KJ

 

[OneIron]

http://www.ebay.com/itm/Cue-Lathe-Dr...item27be250798

According to the seller (Unique Products), this one will work for the CueTec also.
This is assuming the major dia. of the driver's pin is btwn. .354" & .360".
Any bigger than that and it won't fit the CueTec shaft.

KJ

That's the set I bought, I think. The link posted is dead but it was a set of 10 drivers (I think) for about $210.00. I'll confirm by checking my PayPal invoices. These are outstanding drivers, very accurate. I haven't had a CueTec in my shop since I bought them so I wasn't sure if I had a driver that worked.

I'll mic the diameters to find one that may work. Do you know the TPI?

 

[Dirtbmw20]

That's the set I bought, I think. The link posted is dead but it was a set of 10 drivers (I think) for about $210.00. I'll confirm by checking my PayPal invoices. These are outstanding drivers, very accurate. I haven't had a CueTec in my shop since I bought them so I wasn't sure if I had a driver that worked.

I'll mic the diameters to find one that may work. Do you know the TPI?

Here's the link to the 12 piece set from that same seller. I didn't buy the complete set but I bought the ones I use the most from the same seller.

http://www.ebay.com/itm/Cue-Repair-...044?pt=LH_DefaultDomain_0&hash=item27b155f4f4

 

[OneIron]

Here's the link to the 12 piece set from that same seller. I didn't buy the complete set but I bought the ones I use the most from the same seller.

http://www.ebay.com/itm/Cue-Repair-...044?pt=LH_DefaultDomain_0&hash=item27b155f4f4

That's the set I have. Most accurate set I've used. Recommended.