re-wrapping a cue

[D-Rock]

I'm planning on rewrapping an old lucasi I have. I don't want to spend the 40 bucks to have it done professionally because its pretty much just a house cue and probably isn't even worth 40 bucks! I found I can get wrap to do one cue for about 5 bucks and I figure anything I do is better then the unravling mess on it now. How should I go about doing it? are the ends glued or tied? any pointers to send me in the right direction would be appreciated.

Thanks!

 

[KJ Cues]

Buy a wood lathe = $100
Add sewing mach. mtr. drive & mount = $50/75
Buy press roller & burnisher = $150
Instructional DVD = $30.
Additional wraps (JUST IN CASE you don't get it right the first time) = $20.

OR

Take it to someone that actually knows what they're doing = $40.

You do the math.
How much did you say this cue is worth?
Am I being honest with you? = TOTALLY !!!

Sometimes, going on the cheap turns-out to be WAY more expensive.
Not yet convinced = Duct tape.

 

[cueman]

Get a little white glue and a drill and some tooth picks. Stick one end in the hole and break off the tooth pick. Then wipe some glue on a couple of inches and hand wind it as tight as you can get it. Put some glue on a couple more inchs and repeat the process. When you get to the end stick it into another 1/16" drilled hole and break the tooth pick off. Without a lathe you probably won't be able to press it, so now you should have a rough feeling linen wrap. It that is not good enough then I suggest going with one of the two options the other poster gave you. But since you say anything is better than nothing this should be better than nothing. Or you could go buy a tennis racket grip and install it. It would be easier to get to look nice.

 

[D-Rock]

I do have a wood lathe with a foot switch if that helps. What do I have to do to press it?

 

[ARROWCRUSHER]

Buy a wood lathe = $100
Add sewing mach. mtr. drive & mount = $50/75
Buy press roller & burnisher = $150
Instructional DVD = $30.
Additional wraps (JUST IN CASE you don't get it right the first time) = $20.

OR

Take it to someone that actually knows what they're doing = $40.

You do the math.
How much did you say this cue is worth?
Am I being honest with you? = TOTALLY !!!

Sometimes, going on the cheap turns-out to be WAY more expensive.
Not yet convinced = Duct tape.

EXACTLY !! Theres alot more to it the what most think and especially if they never seen it done before. And if they think you just rap it around ,,,LOL. Go ahead have fun, post pictures when you are finished please ...

 

[thefonz]

why not leather?

i've got a break cue that had the linen wrap come unraveled. i took it to a leather shop and they glued on a piece of leather for 15 bucks, worked for me! probably cheaper if you bought a scrap piece of leatherette or leather and glued it on yourself.

 

[manwon]

Buy a wood lathe = $100
Add sewing mach. mtr. drive & mount = $50/75
Buy press roller & burnisher = $150
Instructional DVD = $30.
Additional wraps (JUST IN CASE you don't get it right the first time) = $20.

OR

Take it to someone that actually knows what they're doing = $40.

You do the math.
How much did you say this cue is worth?
Am I being honest with you? = TOTALLY !!!

Sometimes, going on the cheap turns-out to be WAY more expensive.
Not yet convinced = Duct tape.

Great post and right on target, but it would funny to see his results!!!!:grin:

 

[manwon]

I do have a wood lathe with a foot switch if that helps. What do I have to do to press it?

This step takes a little practice, however, below is a rough idea that will work with practice!!!!

I use two equal sized pieces of wood that are hinged on one end. First let the glue set, and then wet the linen with a damp towel. Next spin the cue in your lathe at lets say 1500 to 2000 RPM'S and slide the two pieces of wood the length of the wrap without touching the cues finish. If you are doing it right it may smoke a little bit but that is normal.

Also make sure that the wood used is a hard wood with no sap or the friction will stain the linen, also make sure the surface that touches the wrap is sanded very very smooth before pressing.

Good Luck, but I still think that it will cost you more than $40 before you are done just like KJ stated.