Unknown Sneaky Pete Cue

[deep]

Picked this cue up recently. Though there are no makers name / logo on the cue it appears to be very well made. Very nice birdseye forearm into what looks to be a cocobolo butt section, shaft looks old, tight grain and dense at nearly 4.4oz. The one strange thing is how the bumper has been fitted, it looks like the recess has been cut out by hand as it looks very rough compared to the rest of the cue, anyone seen anything like this before??

 

[Frosty]

I’ve seen house cue conversions where they drilled out the ass end like this and then drilled and tapped a smaller channel inside the larger one to add a weight bolt.

 

[mikemosconi]

Nice piece of wood for an SP and perhaps it was originally without a bumper and the owner had the butt end drilled out for a bumper but I suspect that he may have done that to lighten the back end of the cue as well to change the balance point

I found an old Valley SP and the butt was oversized - had Proficient taper down the butt and it is now as good as any Scruggs or Frey SP in terms of hit and feel. Photo of original Valley SP butt- same as Scruggs utilized - I paid only $40 for it and straight as an arrow.

 

[wacokid9ball]

Looks like one of a thousand SP's i've seen in the seventies

 

[garczar]

Never seen a bumper channel that bad. Looks like it was done with a pocket knife. Just a home made sneaky. Probably hits great, nice wood too. Prob a Schmelke blank. Could be asian but even they wouldn't do a hack job on that bumper channel.

 

[Chopdoc]

Nice looking cue.

We found the maker.

A consortium of forensic cue investigators was established for just this task. It was time consuming, expensive, and exhausting.

We used forensic methods to trace the markings on that bumper channel. Ultimately we had to consult a veterinary dentist who referred us to the #1 wildlife dentist in the nation.

 

[Mensabum]

Picked this cue up recently. Though there are no makers name / logo on the cue it appears to be very well made. Very nice birdseye forearm into what looks to be a cocobolo butt section, shaft looks old, tight grain and dense at nearly 4.4oz. The one strange thing is how the bumper has been fitted, it looks like the recess has been cut out by hand as it looks very rough compared to the rest of the cue, anyone seen anything like this before??

View attachment 921705View attachment 921706View attachment 921707View attachment 921708View attachment 921709View attachment 921710

Not saying this applies to your wand, but I bought an old unmarked Meucci Sneaky, looks very similar to yours, heavy shaft... the weight bolt couldn't be removed as it was part of the butt construct.
Unbeknownst to the guy who had it B4 me, he used a soldering iron and a small chisel to open the weight bolt hole up enuf to get in there with pliers and who knows what all. Thank goodness he was unable to remove it.
The butt is Black Palm. Shaft weighs 4.3, 59".
Cue hits like a train!!

 

[deep]

Nice piece of wood for an SP and perhaps it was originally without a bumper and the owner had the butt end drilled out for a bumper but I suspect that he may have done that to lighten the back end of the cue as well to change the balance point

I found an old Valley SP and the butt was oversized - had Proficient taper down the butt and it is now as good as any Scruggs or Frey SP in terms of hit and feel. Photo of original Valley SP butt- same as Scruggs utilized - I paid only $40 for it and straight as an arrow.

This what I'm thinking, it looks like it was done by an over enthusiastic owner rather that a cue maker.

Hoping to take it out for a few racks this weekend and see how she shoots.

 

[deep]

Played a few racks with the cue today and it plays really nice.

Before leaving for the pool hall I decided to remove the weight bolt, and well its a bit of a monster at nearly 4oz!