Search results

  1. Dave38

    Linseed oil and super glue

    correct, there are no stupid questions....but on this forum lately...by NON cuemakers...there have been....boatloads of stupid answers
  2. Dave38

    Linseed oil and super glue

    for the non-believers....here you go.... Been used by many for years.....
  3. Dave38

    Deluxe Cuesmith Motor

    I have had this only once, and it turned out to be there was a slight defect in the belt....a slightly wider spot, that caused it to happen. I would recommend reaching out to Chris Hightower, he is the best at helping setup/diagnose issues with his lathes
  4. Dave38

    Turning down shaft

    When I am in doubt about this type of request, I always try to contact the manufacturer first. They know all the details needed for such a decision.
  5. Dave38

    Hydro dipping BK Rush

    what is the WORST thing to do to a cue shaft or Butt? .....Immerse it in water..... BUT, In My opinion....it's the same as putting your pen!s in an electrical outlet....you'll be shocked with the results!
  6. Dave38

    Radial Pin tap costs $225 ??

    Atlas's website seems to have turned into a Sh##show......tried logging in, and prices were the same as a guest....took 3 times logging in to get my normal price. Won't be ordering for a bit until they get their sh@t straight
  7. Dave38

    Recommendation for Balbushka repair

    Thanks guys, I will pass the info along. He has a cert. but in the pic he had, could not see who it was from. Thanks, Dave
  8. Dave38

    Recommendation for Balbushka repair

    Have a client with a original babushka with certificate of authentication. He needs to butt cap replaced and so I'm looking for recommendation on who can do the repair but keep the authenticion
  9. Dave38

    Revo Repair Question

    pictures are necessary in order to assist. Both before you tried to fix it, and after.....so people know what was done and therefore how to proceed
  10. Dave38

    Reverse tenon ferrule on a wood shaft

    and that is the bottom line on this subject.....
  11. Dave38

    old valley rails

    I am looking to replace the rubber on an old set of rails from an old valley table that I recovered for a customer last year. I swapped out the old ones with new ones as the rubber was as hard as the wood. The wood is still fine, so I figure I can reuse these for a future table job. Don't...
  12. Dave38

    Removing Power Wraps

    I use a heat gun set to about 600, and a putty knife to scrape the bulk of it, then acetome with a rag for the adhesive left behind, And yes it's a Fkn mess. Hate doing them
  13. Dave38

    How to add a cue extension

    If one is looking for a rear extension, then some mods are needed or the right kit bought depending on how the back end is built. If a mid-cue extension can accomplish the required length the customer wants especially with regards to balance, then .....depends on what the customer likesYes, no...
  14. Dave38

    How to add a cue extension

    If you have a lathe, Drill and tap 3/8x16 for the prather's R-9 type of extension kit and you'll be good to go. If you don't have a lathe, I recommend having a cue repair guy do it so it is perfectly centered.
  15. Dave38

    Best epoxy for assembly

    funny how fast people go quiet when they get called out..................
  16. Dave38

    Gun drills For sale

    What are the overall lengths?
  17. Dave38

    Best epoxy for assembly

    Dude...Really???? who are you? What have you contributed to this forum or the world of cue building/repair? Joey has done quite a bit to move the craft forward.....maybe do some research before being a dick to senior members.....just saying......show us your own work before you criticize others...
  18. Dave38

    Best epoxy for assembly

    There is NO epoxy on that ferrule, If you have been here long enough, Dave has shared multipule times what he uses on ferrules and how he assembles them.
  19. Dave38

    Best epoxy for assembly

    After buying and using the 207, multipule times for finish....IT DOES GO DARK...and DOES NOT DRY CLEAR AFTER IT HAS DARKENED! Spent $$$ and had to refinish cues due to the darkening deal. Maybe if you use the whole can in a month it will be fine but to us small time guys, it WILL come out darker...
  20. Dave38

    Need Help Identifying Weight Bolt

    In order to offer help, knowing the brand of cues could help
Back
Top