Search results

Here is a lightly used, excellent condition, Defy shaft. The narrow part of the shaft looks polished, since I've used the McDermott Cue Silk on that, and it really slides through my ungloved bridge hand pretty well now. Not sure of the tip brand, it plays like a medium layered tip. I'll...

This is a Becue Engage 11.8 shaft, 5/16-14 piloted thread (used on a Joss shaft), 30 inch length, weighs 4.25 oz/121 g. Current tip is an Ultraskin SuperSoft, used exclusively with Taom chalk during the tip's lifetime. The shaft is in excellent condition. There is one burnish mark midway down...

This is a JOS171 which is about 2 years old. The cue is in essentially new condition, not a scratch or flaw on it. It comes with the standard Joss piloted 5/16-14 stainless steel threads. One exterior modification is that the butt cap has been changed to a generic one that can handle an...

I would like to lean on the experts opinions about glue. Usage will be for a small piece of cloth on the slate on the inside of pockets, just so that when the main cloth is cut and extended into the pocket it covers all the slate and looks a little better. Is the 3M 77 spray the best stuff out...

I'm replacing the cloth on the moderately well used table at our local Senior Center. Since they help out another club that I belong to I am doing it for free if they buy the cloth. Done it and leveling before, not a big problem. Nearest mechanic we could pay for is more than an hour and a...

Looking at using Championship Mercury for redoing the 8 foot table at the local Senior Center. They also sell the Championship Mercury Ultra, costs about another $11. Seems the only difference is that the latter is teflon impregnated, so better at resisting spills and stains. Anyone have any...

Really need this for tips and ferrules, and not much more. No intention of ever trying to make cues.

Yes, the ugliest good ball out there. I you happened to buy a set and just can't stand looking at these any more, I'll be glad to take them off your hands. They'll go as a backup set for a non-profit.

I’m working with a non profit to get a donated table set up. I’ve gotten it pretty level, within about unit on my engineers level which is about all that makes sense on a floor that isn’t as stable as you would like. Did a demonstration with my 0.05 mm/m EDA level showing that two people...

Looking for Revo, Becue Engage, Defy or other high end shaft, 12 mm plus or minus a little bit. This is going on a McDermott Gseries with a shaft base diameter of just a touch over 0.850 in. Either 29 or 30 inch is acceptable. Please PM directly--I'll give the courtesy of letting you know if I...

This is a National Gandy, hand made cue from the 1980s. This was the period when Ricco Cervantes made cues for them, so he may have had a hand in the design but there is no proof he actually made this one. If you look closely at the pictures it is clear that this is hand made and inlaid...

Here's an oddball for sale or trade. I obtained a box of 35 Elk Master tips, all 12.0 mm, from the local senior center where I have been repairing tips and cues. These are essentially worthless to them, since every cue they have is 13 mm. So . . . if someone could use these, I'll be willing to...

I’m not sure where to ask this question, so I’ll try here. Is there anywhere in the equipment or other rules that actually specifies how level a table should be? I’ve seen the flatness and coplanar requirement for slates and slate joints, but nowhere can I find anything defining level and how...

I am trying to reweight a group of similar cues and found that the weight bolts are not a standard thread size or something I have seen before. Measuring them they come to 14 mm (very close to 9/16) with a thread pitch of exactly 3 mm. This doesn’t come to an even SAE size so it looks like it...

Looking for both -14 and -18, low deflection shaft. Please contact me directly. Thanks

Looking for the Dr Dave DVDs for his HAPS and SAWS series. Originals only please. Can contact me directly at westerwick@comcast.net.

I was trying to reduce and adjust the weight on my McDermott cue, and was not happy with their approach to weighting, which requires you buy a lighter bolt (or cut down the one you have) in order to reduce the weight. For starts, they cost 9 bucks each at Pooldawg, and cutting the McDermott...