Search results

Thought someone here might also be interested.... https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_ff3=2&toolid=10001&campid=5335988529&icep_item=154232727271 !!!!!!!!!!!!! sold !!!!!!!!!!!!!!!

Specs: Weight - 18.7oz Length - 57.75" Shaft diameter - 12.8mm, 3.5oz Balance point - 19" Butt diameter - 1.2", 15.2oz Joint pin - 3/8-10 Tip - UltraSkin hard Details: Full spliced 4 point verneer with black Italian pebble leather wrap. Brass rings, juma collar and butt cap. Adjustable weight...

Details: Never used Gabon ebony full splice. Very sharp points that are slightly staggard. Shaft is radial laminated hard maple with pro taper and modified to be ultra low deflection. Delrin joint protectors included. Rolls straight together and apart. Made by bjones Custom Cues. Weight -...

Break cue: Full splice Length - 57" Weight - 19.1oz Shaft 13.1mm Pin - 5/16-14 shaft has brass female insert Modified bumper Phenolic collars 1 piece phenolic ferrule/tip Good condition Rolls straight and together and apart Breaks really strong. Used a few times for testing only. Price - SOLD

Anyone seen something like this in and old Huebler? Friend ask me to remove some weight and on investigation I find what looks like a brass plug. Maybe a weight bolt. Can it be removed? I tried a big screw driver and could not budge it. Im also concerned the brass deal might be holding on the...

How many people here would be interested in live threading on a Taig lathe? Live thread both external and internal threads. I wasn't happy with the threads produced by manually hand tapping internal shaft threads. So, I developed a new method that doesn't require a router or Dremel tool and no...

I have a customer that needs a tip replaced on a vantage shaft from predator. Under the tip there is a pad. Does anyone know if that pad is the standard fiber pad available from several sources or is it some special pad only predator uses? Their hype says...."V-Tek Fiber Tip Silencing. Our...

Is this what Prather calls an R9 bumper? http://www.prathercue.com/rubber_bumpers/rubber_bumpers.html or what Meuller calls a Downey bumper... http://www.muellers.com/Downey-Rubber-Bumper,5598.html Im looking for a bumper with that square profile and a little more height. Thanks

What would make the points on a full splice cue uneven after tapering? I tapered using an offset tailstock method. The butt stock was pretty straight before taper, but it did have a major gash along the lower part of the butt stock. I didnt pay any attention to the evenness of the points before...

Whats the weight of a typical finish. Something like clear coat. I know it will depend on how many layers of finish is applied. So maybe a range of weight or weight per coat? Thanks Bob

What do you use to hold stuff in head stock? I have split collets and they are ok for some things, but always require a lot of tweaking to get things on center. I sometimes use painters tape, but its a bit too thin. Leather is usually too thick and soft. Id appreciate suggestions on a flexible...

2 used 24" extruded aluminum taig lathe beds. One has a 10 inch 64 pitch carriage rack. $40 each. Use these as extensions or put them together and make a 48" bed. $70 for both. SOLD Large diameter(2 3/4") steel handwheel with chrome handle for Taig lathe with 64 pitch pinion. SOLD Price...

Cleaning/polishing white phenolic is making me crazy. I'm using 3M sand paper, trying to step through grades from 320, 400, 600,1200, 1500. The weave in the phenolic holds particles and its very hard to make it shine like juma. Id appreciate any tips on how to polish the stuff. There's got to be...

Found an old red leaf dufferin 1 piece bar cue with about a foot broken off. I cut it down to 30". Butt looked pretty clean, so I decide to sand off the clear coat and take a better look at it. A couple of deep dings I can fix. Looks pretty good now, I want to make a breaker out of it. The...

I recently purchased a some inserts from Schmelke. The inserts are for a 5/16-14 pin. The Schmelke webpage says the tap for the insert thread is 12-1.25mm. I bought that tap and its not the correct tap! Does anyone know the correct tap for these inserts...

Was given a bar cue that was headed for the dumpster. Had a broken shaft and rattle in the butt. I decided to drill in and see what the rattle was...assuming it was a lose weight bolt. I was surprised to find this.... I wasnt sure what to expect...but this hunk of steel was the last thing I...

I've been thinking about making an extension for my custom cue. The type that attaches to the butt end of the cue. Looks like the most economical way is to use a 5/16-14 insert and pin. I'd rather use something what would connect faster. Like a uniloc, but I dont want to spend a lot for taps and...

Got a 1st gen 314 with a cracked ferrule in for repair. Seems solid Titan rod is hard to find. Are there sources? I only need 1 for repair but would be nice to have a few more for the next repair. If I cant find some Titan rod...whats the best alternative to keep the shaft low deflection...

Tenon Threader 5/16-18. These are used, but function as designed. $25 each includes shipping in usa. Cheers Bob

Taig headstock with 3 jaw chuck with indexing pulley from Mid America Pool. Bore .590 $SOLD$ includes shipping to usa only. Cheers Bob