BanditNC
- Thread starter JoeyInCali
- Start date
Here are some of Ed's ebonies he's been torturing for 3 years.
He says, if they rot, they don't deserve to be made into cues.
Some have survived and will be processed soon.
He says, if they rot, they don't deserve to be made into cues.
Some have survived and will be processed soon.
Last edited:
Thnx Kent.
Here is the latest pic.
Router mount is being made right now by Ed.
JoeyInCali said:
Thnx Kent.
Here is the latest pic.
Router mount is being made right now by Ed.
A dremel would look good on it
mmmm.... I think I could see a misalignment there... a few thousandths perhaps... oh and like backlash goin both ways... too inaacurate... dang it joey thrash that thing.... oh I have a small junkyard just outside my shop window... that' very much welcome.....
Nice try.hadjcues said:A dremel would look good on it
mmmm.... I think I could see a misalignment there... a few thousandths perhaps... oh and like backlash goin both ways... too inaacurate... dang it joey thrash that thing.... oh I have a small junkyard just outside my shop window... that' very much welcome.....
Better get here and see it then pick up your woods.
I'm outta here in 3 days.
We just came back from Chinatown to pick up some goodies.
Took the train then "some" walking.
Specs: Currently 4-axis but 6-axis ready.
X-axis: THK rails and 4 SR15 linear bearing trucks, 40 inches of travel
1/2-13 all-thread with tiger bronze nut and spring-loaded
anti-backlash nut. *depending on performance may be replaced
with balscrew. Thrust bearings on both ends of drive screw and
flex coupling to 500 oz/in holding torque step motor.
Y-axis: NB low profile wide rails with 4 bearing trucks, 4.25" travel
THK 5mm pitch ballscrew with thrust bearing end mounts, 267 oz/in
step motor
Z-axis: NB low profile wide rails with 4 bearing trucks, 4.25" travel
THK 4mm pitch ballscrew with thrust bearing end mounts, 267 oz/in
step motor
A-Axis: 3" chuck coupled to a Hi-T Drive harmonic drive system delivering
a resolution of 0.0029 degree per microstep.
B-axis: 45 degree tilt manual at the moment but automation ready
C-Axis: up to 10 degrees of swivel. Manual at the moment but automation
ready.
Capabilities:
1. Inlay part cutting
2. 4D Inlay cavity cutting
3. Simultaneous 2 butts tapering *compound taper capable
4. Simultaneous 2 shafts tapering
5. Ring billet making (inlay and cavity) *any number of divisions
6. V-groove cutting *any number of points
7. Folded veneer mitreing
8. Point stock prepping for perfect 90 degree angles
9. long axis and wrap-around engraving or scrim with proper spindle
replacement.
10. in-line or wrap-around 3d carving
Future add-on capability (under development):
1. Internal and external thread grinding
2. Main and A-joint bolt hole boring.
3. Clear-coat application.
X-axis: THK rails and 4 SR15 linear bearing trucks, 40 inches of travel
1/2-13 all-thread with tiger bronze nut and spring-loaded
anti-backlash nut. *depending on performance may be replaced
with balscrew. Thrust bearings on both ends of drive screw and
flex coupling to 500 oz/in holding torque step motor.
Y-axis: NB low profile wide rails with 4 bearing trucks, 4.25" travel
THK 5mm pitch ballscrew with thrust bearing end mounts, 267 oz/in
step motor
Z-axis: NB low profile wide rails with 4 bearing trucks, 4.25" travel
THK 4mm pitch ballscrew with thrust bearing end mounts, 267 oz/in
step motor
A-Axis: 3" chuck coupled to a Hi-T Drive harmonic drive system delivering
a resolution of 0.0029 degree per microstep.
B-axis: 45 degree tilt manual at the moment but automation ready
C-Axis: up to 10 degrees of swivel. Manual at the moment but automation
ready.
Capabilities:
1. Inlay part cutting
2. 4D Inlay cavity cutting
3. Simultaneous 2 butts tapering *compound taper capable
4. Simultaneous 2 shafts tapering
5. Ring billet making (inlay and cavity) *any number of divisions
6. V-groove cutting *any number of points
7. Folded veneer mitreing
8. Point stock prepping for perfect 90 degree angles
9. long axis and wrap-around engraving or scrim with proper spindle
replacement.
10. in-line or wrap-around 3d carving
Future add-on capability (under development):
1. Internal and external thread grinding
2. Main and A-joint bolt hole boring.
3. Clear-coat application.
Last edited: