Brunswick pool table identification required

gazman100

Brunswick Gold Crowns - Qld Australia
Silver Member
Hi all,
I purchased this Brunswick pool table yesterday, pulled it apart and got it it unloaded at my place.
Please find the pic's below at it's pick up location.
It has never been in a pool hall and was owned by an old guy for over 40 years.
It was then purchased as you see it from another guy who owned it for over 10 years until I picked it up yesterday.
This this is a bit of a find.
However I don't believe it's a Gold Crown as some things don't add up.
I have searched high and low for info on this table however I've come up blank, so I would appreciate your thoughts as to what model of Brunswick this is.
I've included some info above the images below.
By the way the table is absolutely gorgeous and is in extremely good condition.

The Brunswick as I picked it up at it's location.
20250318_161759.jpg



20250318_161806.jpg



20250318_161820.jpg


Dated 1964 under all of the corner castings.
20250320_102524.jpg


Rails are near mint.
There are no score counters at the end rail
20250320_102425.jpg



The frame is extremely well built however it's not a Gold Crown frame.
20250320_102627.jpg



20250320_102637.jpg


The rails are a Gold Crown 1.
Figure 8 in perfect condition, no lifting or tear outs.
T bracket for the casting bolt.
GC1 rail trim.
20250320_110555[1].jpg


Slate is in near mint condition.
Solid 1 inch timber backing nothing warped.
Love the warning sticker all though it should have been bigger. Lol.
20250320_102434.jpg



Skirts have a metal bracket instead of the GC1 alloy swing brackets.
Notice the clips at the bottom. I believe these are to hold a plastic skirt however none came with the table. I asked the owner about them as well and he didn't know about it.

20250320_102218.jpg


So there you have it.
When you first look at it it's a GC 1
It has slight differences to a Gold Crown when you tear it apart.
Can anyone ID this table.
Thanks in advance
 
Last edited:
My "Made in Canada" Anniversary has a similar frame. It looks like this type of frame was used in Canadian table as well as the traditional frame we all know.

Here is a link to the tread


Martin
 

Attachments

  • 370204-0d51726316fcf25e648fd50ac2fa761d.jpg
    370204-0d51726316fcf25e648fd50ac2fa761d.jpg
    9.3 KB · Views: 31
Possibly, my Anniversary is identified as such on the name plate but Gold Crown was probably different.

I dont know exactly when Brunswick stopped building tables in Canada. I'm guessing somewhere in the 70's. I own a Gold Crown cue rack that seems to be built around 1970 in Canada.
 

Attachments

  • 2025-03-21_10-49-06.jpg
    2025-03-21_10-49-06.jpg
    47.8 KB · Views: 30
  • 1.jpg
    1.jpg
    123 KB · Views: 31
Interesting reading, thank you.

BTW, I did not realised that the OP is in Australia, even more intriguing .
 
Last edited:
Interesting reading, thank you.

BTW, I did not realised that the OP is in Australia, even more intriguing .
Yes,
These tables are very difficult to fine here.
Even harder to find one which has always been privately owned😁
 
Interesting for sure. Do the aprons bolt to the other side of the Figure 8's? I like the clips on the bottom of the aprons for the plastic skits. Those would make them much easier to navigate vs being screwed in.
 
Yes the aprons bolt to the figure 8.
I'm going to change them out to the regular skirt blocks as used in the later gold crowns.
 
I dont know exactly when Brunswick stopped building tables in Canada.

Brunswick of Canada closed in 1971. This article is from the August 4, 1971 Montreal Gazette.

I have not searched the AZB forum on this matter but I seem to remember a long time ago this matter of early Canadian Gold Crowns having a different frame, and perhaps some other details, did come up. I could be wrong, but I do seem to remember some discussion about something like this before.

By the way, I don't know anything about tables really. I have had this ad for ten years in my Brunswick of Canada folder with my cue research because I have Brunswick of Canada cues.

montreal gazette 1971 - Crop.png
 
Last edited:
Another detail that make me think this is a Canadian table is the use of Robertson head screws (square drive)


1742906445280.png
 
Last edited:
Robertson screws are great. Use them all the time. Used for deck screws , framing screws and all kinds of other things. Just went through about 3000 of them strapping a roof.
 
This is definitely a Canadian thing and not that common in the US, especially at that time. Are they a common thing in Australia ?

A little history here :

The phillips head screws is common in Australia.
The Robertson screws are kind of unique here.
So I've come to the conclusion that this GC1 was made in Canada hence why it is slightly different to the other GC's I've worked on .😀😀😀
 
Back
Top