Here it is.. Go ahead and steal it at this price.. This is a cash only special.. If you look on ebay under the completed items there is a Jensen just like this one and it sold for $1000 not long ago. Only a couple small differences between the two cues.
Last chance at it here before I take her to eBay and give it a shot as much as I dislike the idea.
Very good hitting Jensen custom by Mike Johnson. Believed to be in original condition and made late 80's to early 90's. Just a few very hard to notice small dings in the whole cue.
One in the forearm and I saw three in the butt sleeve. Definitely needs a re-wrap done. It's not coming off just looks very worn out. Few finish spots on the butt plate and at bottom of plate. Not real bad in my opinion.
Checked it last night and the cue rolls straight. For added protection to the buyer the cue is available for a refund minus shipping costs if not satisfied. Cue must be returned in the same condition as sent and you must contact me about wanting a refund within 48 hours of receiving the cue which I think is a fair amount of time.
Specs:
4 point with four veneers and a split point inside - Veneers are - Green, Maple, Red, Black.. 4 points are not even at top.
4 ebony inlays in the butt sleeve with I believe an Ivory inlay in each. Not claiming it as Ivory as I'm unsure but I do see grain in it and was told it is Ivory.
The butt plate has three rings of Red, Maple, Black.
5/16x14 piloted steel joint
Cue weighs 19.8 and 19.7 on my scale. Does not have a weight bolt and is not drilled for one.
Shaft #1: 4.4 ozs, 12.98 mm at tip, 12.9 mm and end of ferrule where shaft meets.
Shaft #2: 4.3 ozs, 12.4 mm at tip, 12.6 mm at end of ferrule where shaft meets, 12.74 mm two inches under ferrule.
Ferrules could be Ivory or might be Micarta. As you can see they have a yellow tint. I think the tips are a Moori and a Talisman but not sure.
SOLD Pending Payment
Thanks,
Josh Hillard
Last chance at it here before I take her to eBay and give it a shot as much as I dislike the idea.
Very good hitting Jensen custom by Mike Johnson. Believed to be in original condition and made late 80's to early 90's. Just a few very hard to notice small dings in the whole cue.
One in the forearm and I saw three in the butt sleeve. Definitely needs a re-wrap done. It's not coming off just looks very worn out. Few finish spots on the butt plate and at bottom of plate. Not real bad in my opinion.
Checked it last night and the cue rolls straight. For added protection to the buyer the cue is available for a refund minus shipping costs if not satisfied. Cue must be returned in the same condition as sent and you must contact me about wanting a refund within 48 hours of receiving the cue which I think is a fair amount of time.
Specs:
4 point with four veneers and a split point inside - Veneers are - Green, Maple, Red, Black.. 4 points are not even at top.
4 ebony inlays in the butt sleeve with I believe an Ivory inlay in each. Not claiming it as Ivory as I'm unsure but I do see grain in it and was told it is Ivory.
The butt plate has three rings of Red, Maple, Black.
5/16x14 piloted steel joint
Cue weighs 19.8 and 19.7 on my scale. Does not have a weight bolt and is not drilled for one.
Shaft #1: 4.4 ozs, 12.98 mm at tip, 12.9 mm and end of ferrule where shaft meets.
Shaft #2: 4.3 ozs, 12.4 mm at tip, 12.6 mm at end of ferrule where shaft meets, 12.74 mm two inches under ferrule.
Ferrules could be Ivory or might be Micarta. As you can see they have a yellow tint. I think the tips are a Moori and a Talisman but not sure.
SOLD Pending Payment
Thanks,
Josh Hillard
Last edited:
