How Would You Shoot the 4?

There are several methods of getting from the 4 to the 5 ball. How would you do it?

bbb.jpg
 
Playing the 4 in the right corner of course with just a little left bottom english and go 3 rails. This one is all about the speed!:thumbup:
 
If for some reason I didn't want to play the 3 rail shape, I'd consider banking the 4 back between the 5 and 6 with a little low right to snug the cue ball up behind the 8
 
There are several methods of getting from the 4 to the 5 ball. How would you do it?

View attachment 369565

If I "like" the speed of the table, I may play the two-rail out the middle position. If the table is playing a lot faster than I "like", I'm "dead-balling" the shot and hitting it a bit firmer and bringing it back around 3 rails to "slow" it down into position. As long as you can hit the 5 ball and make it in the corner, then there are several ways to get out from there...none too difficult.
 
I only see two ways. 2 rails to the middle, or 3/4 rails all the way around. 3 rails gives more leeway speed-wise, the 2-rail shot has to stop within about a foot of the target or get hooked, 3-railer a little more. But the 2-railer leaves easier shape to get on the 6.

I'd probably go 2 to the middle (...and then get hooked behind the 7).
 
4 rails. No doubt about getting on the 5 this way. Playing 3 rails for the window between 6 & 8 doesn't interest me in the least.
 
Definitely little bit low and good amount left and medium hard shot for four rails position.

Same as that 3 rail position but shooting 1 rail more makes it almost impossible to miss position, because last two rails have braking sidespin on it.
Also when you have pressure on it's easier shoot firmer shot.
 
Since a stun shot is a scratch, I am using just a little follow and going three rails. From there, the rest is close to all stop shots.
 
I'd probably try the 3-4 rail position using low left. That route not only leaves more room for speed control, but if the 4 misses, a better chance at ending up safe than with the CB at center table.
 
I like going three rails only..hitting the middle diamond on the third rail
is pretty natural....with low left.
I wanna be full on the five so I can get the six in the side...
.....getting shape then is easy for the maroon eight...:D
 
I like going three rails only..hitting the middle diamond on the third rail
is pretty natural....with low left.
I wanna be full on the five so I can get the six in the side...
.....getting shape then is easy for the maroon eight...:D

I agree, (same thing I said) except for the left english. Left will have the tendency to bring it long off the second rail and might hit the six. I would use center ball axis because you are already getting some left on the cb from contact induced spin. I think all you guys putting low on it might find yourselves scratching. Stun shot is a dead scratch.
 
I agree, (same thing I said) except for the left english. Left will have the tendency to bring it long off the second rail and might hit the six. I would use center ball axis because you are already getting some left on the cb from contact induced spin. I think all you guys putting low on it might find yourselves scratching. Stun shot is a dead scratch.
The stun looks very close to a scratch. Low? I might be getting confused but how can anyone go 3 rails to the 5 with low?

Stun run all day long. It will head towards the diamond closest to the corner, and a little left wil swing it onto the second rail the up just short of the middle diamond on the opposite long rail.
 
I like going three rails only..hitting the middle diamond on the third rail
is pretty natural....with low left.
I wanna be full on the five so I can get the six in the side...
.....getting shape then is easy for the maroon eight...:D

Yeah, I did it again and nobody noticed...until you:D.

That's the 7 ball.

ONB
 
Back
Top