Narra on Ebony

T

Tony Zinzola

AzB Silver Member
Silver Member
Just needs Finish and a wrap. 4 Narra Points with Veneers on Ebony. Wrap will be black leather. Should be ready to go in about 10 days.

05-29-08-001.jpg


05-29-08-002.jpg


05-29-08-003.jpg
 
Haha. Thanks. You too. I'm going to change it soon to the one where she actually got the cone with the ice cream. I had to pry it out of her hands. Must take after me.
 
8-ball Rat said:
Nice lookin' cue, sir. Do you do piloted steel joints, too?? :D :D :p
Click to expand...

Most of my cues have a piloted joint with the Radial Pin. Anybody who has bought one like that and ordered another has requested the same joint. I have one cue that is going to be finished at the same time as this that has a piloted radial with a steel joint sleeved over phenolic. The Buyer doesn't want pictures posted yet or I would have shown them because it is a gorgeous looking cue. I can do another type of pin if that is what is preferred.

Thanks
 
Charlie Edwards said:
Absolutely beautiful cue. Nice clean work. Are some of the veneers paper veneers?
Click to expand...


Thanks and yes, there are black paper veneers starting at the point and between each color all the way to the outside.
 
very nice cue....how heavy is this cue? ..I know narra is a heavy type of wood....and can only found in the Philippines.
 
The Butt is 15.1 Oz without the Wrap and the Finish.

Since QJunkie asked. His may or may not be in this group. Many more in the works, but these were handy. One of these days I'll figure out how to take a decent photo.

05-29-08-004.jpg
 
yeah!!!

that's the one... pure hotness. cant say anyone has rocked orange/pink/purple veneers before. :eek:

Thanks Tony!
 
Awesome

Gorgeous cue Tony! What type of material did you use for the joint and buttcap and the ringwork? :cool:
 
Joint and Butt on that cue are Elforyn. Ringwork is silver and ivory. I didn't mention it, but have been asked several times now. That cue is sold. Every cue I have in the works is sold with the exception of one.

Thanks
 
BlowFish said:
I'm not the point cue kinda guy, but your work is top notch. I like it.
Click to expand...

Thanks. I don't usually make cues without points, but I currently have three in the works that should be done soon. Two are already sold. So, I guess that makes two that I Have int he works that are not yet sold. I forgot about the non pointed cues. The one that is available is Ebony Forearm, Ebony Butt, Black Lizard Wrap and the same ringwork as the one in this thread. Joint and Butt will be black buffalo horn. Hmm, maybe I'll use a black G10 pin too, so the cue will be pure black with the exception of the silver and ivory in the rings.
 
Those are all nice cues you have there and looks like a nice clean work.
But I think you have used too many veneers and you make the main wood a small part of the points and it looks too short, it is half of the height of the points especially at the Narra on Ebony cue.
 
ApoDra said:
Those are all nice cues you have there and looks like a nice clean work.
But I think you have used too many veneers and you make the main wood a small part of the points and it looks too short, it is half of the height of the points especially at the Narra on Ebony cue.
Click to expand...

I can understand what you're saying, but I doubt they are short. My points are considerably longer than most, so the inner point wood is probably as long as a lot of the cues out there that have a couple of veneers on them. However, I could understand if you think they look narrow. There's no doubt they are narrower in the bottom.

I don't really use more than 4 veneers except the papers and if you add them all up they are less than a veneer.
 
You must log in or register to reply here.
Back
Top