Pocket Blocks, LONG case and D-12 wanted

P

Pool Goddess

Registered
I am looking for a set of Pocket Blocks. I'm not sure what the proper name is for them, but the fit into the pockets on a pool table so you can use it for billiards. Does anyone know where I can find a set? Used would be fine!

I'm also looking for a cue case for 3 cues that will hold a snooker length shaft. I'd prefer the tube type case.

I'm also looking for a D-12 McDermott cue in good to excellent condition.
Can anyone help me??
 
Pool Goddess said:
I am looking for a set of Pocket Blocks. I'm not sure what the proper name is for them, but the fit into the pockets on a pool table so you can use it for billiards. Does anyone know where I can find a set? Used would be fine!

I'm also looking for a cue case for 3 cues that will hold a snooker length shaft. I'd prefer the tube type case.

I'm also looking for a D-12 McDermott cue in good to excellent condition.
Can anyone help me??
Click to expand...

Mind if I ask...what is a snooker length shaft's length???

Shorty
 
You should be able to buy the pocket inserts at any billiard supply store. They may have to measure your pockets though in order to get a good fit. An Instroke (even the cheaper Instrokes) should hold the shafts in question. I can't help you with the Mcdermott, but I'm sure there are dozens of people here that can sell you one or get you one.
 
Pool Goddess said:
The shaft is 31" long, approx 2" longer than a standard shaft.
Janet
Click to expand...
On some snooker cues, the shaft makes up 2/3 of the cues length. I would think, about 36-37 inches.

Tracy
 
RSB-Refugee said:
On some snooker cues, the shaft makes up 2/3 of the cues length. I would think, about 36-37 inches.

Tracy
Click to expand...
She's not asking how long the shaft is. She's TELLING that it's 31 inches. I checked my Instroke and it will accommodate a 31 inch shaft. Barely.
 
Vonn31 said:
She's not asking how long the shaft is. She's TELLING that it's 31 inches. I checked my Instroke and it will accommodate a 31 inch shaft. Barely.
Click to expand...

Vonn,

Was there any extra room when you had the 31" shaft in there or did you have to squeeze it in there as it was?
 
Vonn31 said:
You should be able to buy the pocket inserts at any billiard supply store. .
Click to expand...

I think they are a fable. people post here looking for these every so often and I dont think they're available. Somebody please post if they are coz i want some too.
 
Rackin_Zack said:
Vonn,
Was there any extra room when you had the 31" shaft in there or did you have to squeeze it in there as it was?
Click to expand...
I don't have a 31 inch shaft. I measured 2 inches from the top of a 29 inch predator shaft. I took a picture but it's hard to see. I deleted the picture. It was too big and too blurry. Actual measurement is about 31 3/8 inches.
Black-Balled said:
I think they are a fable. people post here looking for these every so often and I dont think they're available. Somebody please post if they are coz i want some too.
Click to expand...
You may be right. Finding information on them is difficult. I originally said they exist, but I could be wrong.
 
Last edited:
I found a set on the web. Australia I think. They told me they are 90.00 a set. They called them empire rails.
 
An Artisian or Tooled instroke will diffenitly hold a snooker shaft....I have both and have to dig my fingers into it for a regular shaft as it is.

The depth is 32 1/4 , and thats not including the extra...say 1/4 inch or so with the padding.
 
Thanks for all the help! Still looking for Pocket Blocks!

I know they used to make these and sell them in a catalog. I cannot find them anymore and would like to get a set for my 9 ft Brunswick. So if you run across them in a catalog you have, keep me in mind! Thanks!
 
matthew staton said:
you can buy your pocket reducers at mullers.
Click to expand...


pssssssst.................She's not looking for "reducers". Man, I hope you play better then you read :D (j/k)
 
You must log in or register to reply here.
Back
Top