Porter Cable router mounts ready to ship.

DanO

DanO

AzB Silver Member
Silver Member
I have ten mounts assembled with all hardware including the bottom 5mm alignment dowels. Below is a list of ten interested parties from PM’s and the last thread.

$80 including shipping and fees to DanO@Timocues.com Paypal.

I will hold for two weeks, then move on. Not a problem if you have changed your mind after reading the previus thread, or have made something else during the wait. Just let me know.

Thank you for your interest.

CamposCues - SHIPPED
GrimmCustom Cues - SHIPPED
Grimm Reaper - SHIPPED
Dirtbmw20 - SHIPPED
JimBob - SHIPPED
juspooln SHIPPED
deadbeat - SHIPPED
jecues - SHIPPED
cueguy - SHIPPED
tlayne - SHIPPED
 

Attachments

  • Router mount.jpg
    Router mount.jpg
    75.4 KB · Views: 1,182
  • Router mount 2a.jpg
    Router mount 2a.jpg
    45.8 KB · Views: 1,179
Last edited:
You are welcome. As much as I'd rather hand deliver it to Nashville, it will go out in the morning. I will PM the tracking number.
 
I don't have the extra cash right now and I'm not on the list. So are you going to have a second batch done if there is enough interest.

Sent from my SCH-I545 using Tapatalk 2
 
DanO said:
I have ten mounts assembled with all hardware including the bottom 5mm alignment dowels. Below is a list of ten interested parties from PM’s and the last thread.

$80 including shipping and fees to DanO@Timocues.com Paypal.

I will hold for two weeks, then move on. Not a problem if you have changed your mind after reading the previus thread, or have made something else during the wait. Just let me know.

Thank you for your interest.

CamposCues Chris Campos - SHIPPED
GrimmCustom Cues Rich - SHIPPED
Grimm Reaper Kyle Grimm - SHIPPED
Dirtbmw20 Lee Casto
JimBob JimBob
juspooln Bill Pelham
deadbeat
jecues
cueguy Larry Hale - SHIPPED
tlayne
Click to expand...

Can this adapter be fitted to a full size lathe such as a Grizzly or would it just be easier to construct a new one? If it is feasible then put me on your waiting list.

Thanks,
Dick
 
rhncue said:
Can this adapter be fitted to a full size lathe such as a Grizzly or would it just be easier to construct a new one? If it is feasible then put me on your waiting list.

Thanks,
Dick
Click to expand...

If you can send me the table mount configuration of your cross slide, and the center height from your slide mount to your headstock, I'll see what I can come up with to adapt to what you need. Even if it's a picture of a napkin sketch. I've worked from less.
 
All ten router mounts have been shipped. Big thanks to everyone for following through.

For those interested that were left out in the cold, I'm going to do another run that will be ready around Feb 1st. Anyone interested who has not PM'd me, please do since February may be as cold as now.
 
Nice

DanO said:
All ten router mounts have been shipped. Big thanks to everyone for following through.

For those interested that were left out in the cold, I'm going to do another run that will be ready around Feb 1st. Anyone interested who has not PM'd me, please do since February may be as cold as now.
Click to expand...

I got mine.
Thanks!
 
I have another batch with the hardware ready to ship. Below is my short list of interested parties. $80 to my Paypal and they will go out this weekend. Dano@timocues.com Shipping is on me unless you reside in Canada, then we will figure out the diffence. Thank you gentlemen.

fradrums
GAtexas1978
JC
screamingelvis
cuetify
Kim Bye
Blue Hog ridr
gmcole
pockets14.1
 
All paid orders have shipped. Expected delivery is Tuesday. I have extras so let me know if anyone else wants in. Thanks guys.
 
When am I getting mine to Canada. It's been three days now.

Just teasin ya Dan. USPS gets it to the border quick. Customs and Canada Post always make me wait. I am used to it by now, trust me on that.

But, am looking forward to a try out tho.
 
Sorry Terry, USPS could not give me an estimated delivery date. Don't stand out in the cold waiting for Sasquatch to deliver. Wait, is that you on your Blue Hog ridr?
 

Attachments

  • blu.jpg
    blu.jpg
    9.9 KB · Views: 164
You must log in or register to reply here.
Back
Top