Radial OB-1 f/s

RunEmOut08

AzB Silver Member
Silver Member
ive got a Radial threaded OB-1 that i need to sell. ive decided to go back to shooting with solid maple shafts. This shaft is in great shape. It has been turned down to 12.5. it has a molavia hard tip on it which plays very similar to kamui. I am looking to get New Price $120shipped. I will also include an extra molavia tip with purchase buyers choice of either hard or medium. I will post pics if needed but im sure everyone knows what an OB-1 looks like. Thanks for looking!
 
Last edited:
the shaft is 29" and as far as what radial pin its for i was unaware that OB made multiple radial pin threads... the shaft fit perfectly on my Diveney which was a standard stainless radial. it is the plain black collar

thanks for looking
 
Last edited:
RunEmOut08 said:
the shaft is 29" and as far as what radial pin its for i was unaware that OB made multiple radial pin threads... the shaft fit perfectly on my Diveney which was a standard stainless radial

thanks for looking

the thing about radial pins is that what's standard to one cuemaker might not be standard to another.
 
but arent they all threaded the same? the only difference that I have ever seen in radial pins is the length of them... but i could be wrong... any info you might have on that would be useful thanks
 
RunEmOut08 said:
but arent they all threaded the same? the only difference that I have ever seen in radial pins is the length of them... but i could be wrong... any info you might have on that would be useful thanks

they're actually not all threaded the same. i had 2 cues that both had radial pins and out of curiosity one day i tried interchanging the shafts. they didn't fit.

who knows though maybe i did it wrong.
 
poolplayer2093 said:
they're actually not all threaded the same. i had 2 cues that both had radial pins and out of curiosity one day i tried interchanging the shafts. they didn't fit.

who knows though maybe i did it wrong.

I've actually heard of that before although every radial I've encountered has been the same. I'm fairly certain that the Radial pin itself refers to one unified thing, while there are two iterations of that one thing (one old and one "new" aka the current one).

Hope that helps! :thumbup:
 
Maybe you should ask this in the Cuemakers section, but from my experience I believe proper "Radial" pins as sold by Uniloc are usually interchangeable, but some cuemakers vary in the amount of the lead part of the pin they turn down and the material they are made of. I have seen some apparent copies of the design (EG Mezz "Wavy" joint) that I would assume would not be directly compatible.

I bought a generic OB-1 Radial for my Capone, and it is noticeable that the fit of the OB-1 is a bit less tight than the original Capone shafts. I believe this is due to some cue makers deliberately undersizing the tapped hole in the shaft to get a very tight fit rather than the pin itself being differently sized.
 
RunEmOut08 said:
ive got a Radial threaded OB-1 that i need to sell. ive decided to go back to shooting with solid maple shafts. This shaft is in great shape. It has been turned down to 12.5.

Who turned down the shaft to 12.5MM? Did you order it like that or have it changed afterwards?
 
I had a cue maker locally turn it down slowly with sand paper. I talked w/ Royce at OB and he said that it was fine. He did say that if you took it below 12.3 or so that you could start to get into the foam core.
 
I got him to basically leave the taper the same as a typical OB1 b/c the taper was fine but 12.75 was just a lil too big for my taste.
 
new price 130 shipped with the extra tip.... would like to sell it soon b/c i need to make room in my case for my new shafts.... thanks!
 
Back
Top