(3) 18 TPI threaded stainless collars.
(2) Rubber bumpers 3/8-16 threaded stems I believe.
(11) Brass rings Odd mix of .030 and .015 thick
(10) Nickel-Silver .030 thick (4) butt size and (6) joint size
(3) Sterling Silver rings 1 butt size and 2 joint size .015 thick
(1) 303 S.S UNI LOC joint pin
The above stuff alone cost more then the asking price for this entire lot, but there's more included-
(7) Black phenolic trim rings with aluminum filled slots, The three joint size rings and 1 of the butt size rings are close to the same thickness, but the other 3 butt size are much thinner.
(1) short piece of joint size matching billet to cut your own thickness from, over 1" of usable rod left on It.
(10) strips of the same aluminum used to make those trim rings, more then enough to make another 5"-6"s of matching billet. Just slot your Phenolic, and fill with these.
(1) piece of buck horn joint size material. Just shy of 1-1/2" long. Nice solid piece. Minimal pith if any.
(3) Rolls of Micro mesh cloth backed strip. Works well for sanding and polishing most metals, does good job on stainless and aluminum, but works on other materials as well. can be used as Wet/Dry. Anyone that has used this stuff knows of the quality and high pricing. These rolls are wound tight so there's quite a bit more here then meets the eye.
I'll take Sold!!! for the lot + $5.50 to ship in a small priority mail box. PayPal for Payment, US shipping Only Please. First person to Pm, and make Payment Gets It. If You snooze on payment and someone else gets It, then Please don't get upset. I always give the person in line priority, then go from there, but they have to do their part too. Also If You Pm, I'm not around at the time, and You don't receive a message right back, Then please Be patient. I will contact the first person in line as soon as I am able check My PM's. I'll be up for a little while, but eventually will have to get some sleep before I have to get up, and go pick up some work I have to do in the afternoon.
Thanks for looking, Greg
(2) Rubber bumpers 3/8-16 threaded stems I believe.
(11) Brass rings Odd mix of .030 and .015 thick
(10) Nickel-Silver .030 thick (4) butt size and (6) joint size
(3) Sterling Silver rings 1 butt size and 2 joint size .015 thick
(1) 303 S.S UNI LOC joint pin
The above stuff alone cost more then the asking price for this entire lot, but there's more included-
(7) Black phenolic trim rings with aluminum filled slots, The three joint size rings and 1 of the butt size rings are close to the same thickness, but the other 3 butt size are much thinner.
(1) short piece of joint size matching billet to cut your own thickness from, over 1" of usable rod left on It.
(10) strips of the same aluminum used to make those trim rings, more then enough to make another 5"-6"s of matching billet. Just slot your Phenolic, and fill with these.
(1) piece of buck horn joint size material. Just shy of 1-1/2" long. Nice solid piece. Minimal pith if any.
(3) Rolls of Micro mesh cloth backed strip. Works well for sanding and polishing most metals, does good job on stainless and aluminum, but works on other materials as well. can be used as Wet/Dry. Anyone that has used this stuff knows of the quality and high pricing. These rolls are wound tight so there's quite a bit more here then meets the eye.
I'll take Sold!!! for the lot + $5.50 to ship in a small priority mail box. PayPal for Payment, US shipping Only Please. First person to Pm, and make Payment Gets It. If You snooze on payment and someone else gets It, then Please don't get upset. I always give the person in line priority, then go from there, but they have to do their part too. Also If You Pm, I'm not around at the time, and You don't receive a message right back, Then please Be patient. I will contact the first person in line as soon as I am able check My PM's. I'll be up for a little while, but eventually will have to get some sleep before I have to get up, and go pick up some work I have to do in the afternoon.
Thanks for looking, Greg
Attachments
Last edited:
