Search results

Didn't mean a 9' bulb, sorry for confusion. For their 9' light Diamond recommends a 59 watt, single pin, F096/741/ECO bulb. The dimensions for the 9' light are 26" x 102" Hope that clears it up! Mike

Diamond light dimensions The 9 footer is 26"x102" and uses 9' - 59 watt - single pin - F096/741/ECO bulbs. Mike

Looking to buy a 314-2 radial shaft with black collar w/silver ring. Thanks much! Mike mike@card-it.com or PM

Geno, Are you coming to South Florida or just Tallahassee? I remember you saying you have family down here. If you do, I'd like a lesson. Mike

New Predator shafts Please send me a list of what you have and prices. Thanks. Either PM or mike@card-it.com cardit

South Florida mechanic Frank, I have nothing but good things to say about Brett Geisler, Atlas Billiards. My GCIII plays very well after he extended the rails, installed new rubber, put in new boots, and covered with Simonis 860. Mike Coral Springs Brett's Cell: 305-720-4239

I'd like to give the chalk a try, too. PayPal on the way. Mike

Gene, Thank you very much for the time you spent with me Wednesday night. I found the session very informative and definitely had my eyes 'opened' (pun intended!). I just hope no one else in my league takes you up on this free offer, unless of course they're on my team. Folks, this is good...

I'm not replacing the P2; I like it a lot. I was looking at buying a second shaft for it then came full circle deciding I'd just buy a second cue. I -need to re-wrap or re-press the linen on the P2 and maybe refinish it to remove a few chips. This way I'd be able to send it away and still...

Thanks for the feedback. The Ikon 8 has the same curly maple as my P2, and it is very well figured. Does anyone have thoughts about buying the 1999 predator as opposed to a newer one?

Hi all, I'm considering buying a Predator Ikon 8. Having played with a P2 for the past 3 years should I expect much difference in 'feel' between the two cues? 314-2 on each. Any negative/positive thoughts about the Ikon? I also looked at a mint 1999-5 with a 314 shaft with the thought of...

Sunday Does anyone know the times of tomorrow's matches? Thx Mike

South Florida mechanic I've been very pleased with Brett Giesler, Atlas Billiards, who has worked on my GCIII (including extending the rails and recovering). 954-476-6080 Mike Coral Springs

Hi all, Just picked up this Orchid cue with 2 shafts. Both joint collars butt and shaft) have the word 'Regal' on them. Searching the archives I couldn't find much information. Any help about history/quality/maker would be very much appreciated. Thanks! Mike cardit

There is an additional charge to extend the subrails. It's not included in the re-cushion charge. Is 5" correct for the side pockets? Regretfully, I've not heard of RKC heading to the Ft. Lauderdale area. I'll ask him about the angles.

After a lengthy search and looking at a lot of tables I just purchased a GC III and it'll be delivered and set up next week. I found a mechanic in South Florida that has done rail extensions after speaking with about 10, none of whom had an idea what I was talking about. Side pockets measure 5...

Rooms near Boca You might consider Premiere in Coral Springs; 15 9-foot Gandy's. Open at noon I believe. Also, Corner Pocket on Oakland Park Blvd in Ft. Lauderdale; Gold Crown's and heated billiard tables. A bit of a drive takes you to Hollywood Billiards. Bring warm weather with you. Into...

This table has been in a residence for 14 years and in a pool hall for the previous 35 or so. Any thoughts about quality, playability, etc.? The label underneath says AMF 400 8298. Asking price is $1000. Price seems very high; I've seen GCs lower. Is this a decent table or should I run...

Thanks, Glen. A dealer snapped it up while I was enroute to see it. The search continues. Looking at an oak Diamond today in a bar, asking $2500. Also found a Big G for 'free', needs a couple of new sides. As a woodworker that doesn't phase me. Appreciate your comments to me and to the...

I'm off in a bit to look at a one-owner GC III, disassembled, owner moving to smaller home. Is there anything in particular I should look for when I inspect it? Also, how does one 'diamonize' a III? Is it something I can do myself or is there a mechanic in SE Florida who is competent enough...