Search results

  1. n10spool

    -BRUNSWICK-Pool-Table-Slate-Level-?????

    I think it was a straight edge to rough level frames first use a plane on the frames till there square and flat. then level as normal. interesting, Craig
  2. n10spool

    How to remove rail counters????

    It comes out in one piece. When you drive out the pin it should be tapered slightly or have a grooved end that will be the large side mark it or it gets harder to put back together. Draw out a picture of all the parts washers and the order they go. First one is scary the rest are easy to work on.
  3. n10spool

    Nor Cal Cuemaker that uses a 5/16-18 Pin?

    Send a picture to me only 18 thread cues I know of used to work at onetime with oakland bernie. Most names atone here only one I know still uses 5/16-18 is Don Lim older chinese guy 30-40 fancy cues mostly sneakies or rambo style copies.
  4. n10spool

    WTB Two 7' Diamond tables and recover 4

    Tony Dont mess around with any one else Donny will take care of you 100%. If you need an extra hand I'll come down and help but Donny's the man in your area when it comes to Diamonds... Craig
  5. n10spool

    Replacing the cushions

    A good trick is to keep it covered to limit the amount of sun light that gets on it. Most products that are pertrolem based break down from sun light and uv rays. A fun test is to take left over rubber put it on a roof for a year then come back and see which ones like sun light. Craig
  6. n10spool

    Kim Steel pool tables

    Its been awhile since I have worked on a kim steel table. I will be picking a couple up in a week or two then i can till you for sure. I think you can look at the center seams and see where to drill a couple of holes so you can use a machinest screw and screw down into the frame to draw the...
  7. n10spool

    Question for a mech or shop owner

    Did you pay by credit card......Or maybe call manufacture and explain or see who they may want to send out to make factory repairs... Craig
  8. n10spool

    9' GC1 slate

    pins in the slate will be off or need to be removed to match seams. Craig
  9. n10spool

    fake money!

    I got some 20's in hawaii dead perfect but short 1 digit in serial number.later I found out the feds beloved iyt was a time deal someone was try to pass 25,000 worth over a month at all small stores. Feds belive they had picked up 20,000 of it but where not sure how much was really out there...
  10. n10spool

    I search the Name of this Buffalo Cue

    i was told last week in atournament buffalo and bear cues are made by falcon cues.
  11. n10spool

    9' GC1 slate

    Im in sacramento ca I have 2 full sets of slate but one is rebco other is for Gandy both should have bolt pattern to match gold crown rail. Pocket cut radius might be a little bigger.
  12. n10spool

    Pictures of new table

    Looks great you will have lots of fun on it. Looks tight in in the room so dont leave the cue ball on the rail unless it's in your favor.... Craig
  13. n10spool

    ABIA - Who owes you money

    Tap Tap . Dont forget about overtime class action lawsuite i,m in a couple right now from being a cable guy. As for not getting paid on pool tables I turn down alot of work, Or tell them a check price cash price both come with receipt If paying by check I cash it in the middle of install when I...
  14. n10spool

    ABIA - Who owes you money

    So when did the ABIA become a lawfirm in fifty states over night... Nice to see you want to help But im sure the ones that money is owed to dont have a license, insurance or legit registered company. It all needs to be looked at on 1 on 1 to see what the problem is, I have a great success rate...
  15. n10spool

    What Type Of Vehicle Do You Use?

    I use a f150 supercrew pickup 5 foot bed with custom work shell. It will hold gc completly inside anframe outside on ladder rack. It used to be my cableguy truck but now im back fulltime to tables and loving it again. Looking for something new but time will tell. Craig
  16. n10spool

    Streching the Felt

    Orchard supply sells vise-grip 3" wide pliers for about$ 20.00 .you may need to file corners sometimes are sharp. Do a search for mechanics tools or unusal tools about 6-8 months ago several good pictures. Craig
  17. n10spool

    A Big Thanks to the Top Level Specialist and Mechanics--Some of my work

    Very nice, keep it up you will be in big demand in your area. Craig
  18. n10spool

    Proper Torque to Tighten Rail Bolts - Diamond Pro

    Tap tap. 3kushn Craig
  19. n10spool

    Simonis 860 Tear

    Looks like its between the gutter and the facing probably from a watch or rings reaching in to get balls. If it was left of the gutter then it would be the usual slate edge getting hit by the ball so a couple of dabs of super glue should help until recover is in order. Craig
  20. n10spool

    Insurance?

    So who do you have liability insurance. With I've been checking most don't know what a table mechanic is or a pool table is. Craig
Back
Top