Best cheap digital caliper

  • Thread starter Thread starter JC
  • Start date Start date
JC

JC

Coos Cues
This has been discussed here before and I've purchased some real crap based on the discussions.

I have had one of these for several years and a ton of others in the same price range.

This one is best and it's not even close. Bought two more recently and threw all the other junk away. The are just as good as the first one.

www.ebay.com

iGaging Electronic Digital Caliper with Super Large Display for sale online | eBay

Find many great new & used options and get the best deals for iGaging Electronic Digital Caliper with Super Large Display at the best online prices at eBay! Free shipping for many products!
www.ebay.com www.ebay.com

You're welcome
 
JC said:
This has been discussed here before and I've purchased some real crap based on the discussions.

I have had one of these for several years and a ton of others in the same price range.

This one is best and it's not even close. Bought two more recently and threw all the other junk away. The are just as good as the first one.

www.ebay.com

iGaging Electronic Digital Caliper with Super Large Display for sale online | eBay

Find many great new & used options and get the best deals for iGaging Electronic Digital Caliper with Super Large Display at the best online prices at eBay! Free shipping for many products!
www.ebay.com www.ebay.com

You're welcome
Click to expand...
Are these the good ones?
 
My 2¢:

I have a nice set of Mitutoyo calipers, Micrometer, and a set of good Gage blocks.

I compared the measurements from the Mitutoyo calipers and micrometer against a couple sets of Harbor Freight Calipers, using the gage blocks as a standard.

All of the tools were completely within their published tolerances — and the Harbor Freight were accurate to .0005”

After asking on a machining forum, one of the experienced guys said that’s typical - the cheap ones work just fine. They just don’t last as long.
 
www.harborfreight.com

6 in. Digital Caliper

Amazing deals on this 6In Digital Caliper at Harbor Freight. Quality tools & low prices.
www.harborfreight.com www.harborfreight.com

I buy these. I have 4 of them around the shop. They can be had on sale for as cheap as $12. They work just fine and are accurate. At any given time I usually can only find 2 in my shop......

Kim
 
tomatoetom said:
Are these the good ones?
Click to expand...
They are the good ones that are not expensive. Have tried those harbor freight ones. Great if you want them to switch to mm and zero mid measurement. Second time they do that I pitch them in the trash can. I don't currently possess any if that says anything.
 
JC said:
Great if you want them to switch to mm and zero mid measurement.
Click to expand...

I’ve never had that happen to me, but can definitely agree it would be annoying. Are you sure you haven’t angered some sort of pool God and wound up cursed?

You get bonus points if you had a set of vernier calipers reset mid measurement! If that happened, you’re definitely cursed!
 
Coming from a tool room background, I purchased a Mitutoyo 6" and 12" many decades ago and all I do is change batteries.
The cheap ones are just that, they feel cheap, lose their zero, and are just annoying.
Buy once, cry once.
 
Ipmtim said:
Coming from a tool room background, I purchased a Mitutoyo 6" and 12" many decades ago and all I do is change batteries.
The cheap ones are just that, they feel cheap, lose their zero, and are just annoying.
Buy once, cry once.
Click to expand...
I cried for a second time when I dropped mine and shattered the face on the concrete floor. Now I go with the cheap ones. The one I linked doesn't feel cheap and I also come from a very strong tool background having owned and operated a European auto repair shop for 30 years. I know cheap tools when I see or use them. I have a central caliper I bought 40 years ago that still works but the display is very small.
 
I use a Insize caliper now and has done so for some time, I can't really tell much difference between the Insize and Mitutoyo, except for the price.
When it's time for a new one, I'll probably go with Tesa, I like the bigger display and in general I like Tesa products better than Mitutoyo.
 
I’m not a fan of the digital calipers. I have a couple of nice Startetts but I usually leave them in a case. I actually use a 6” dial caliper that has inch and mm made by Anytime Tool. You can get them on Amazon for $36. I keep one in my vehicle for use when I’m out and about and one in my top drawer. They are accurate and will do either measurements I need.
 
I have about 9 harbor freight ones and quite frankly, they work until they don't......I just went thru my batch of them, as I do every few months, and measure a ground rod I have, and they all read within .0005" We build cues....not spaceships....they are more than adequate for the job, IMHO. Do they develope problems? yes....but at $12 a pop....I can throw a few out over the years and still save $$ over the top calipers out there. When I drop them...I don't cry, I check them and if broke, I grab the next one....no big deal, try dropping a Mitutoyo and breaking it, how many do you have in reserve?
 
i use calipers and other machine shop tools for a living,
the cheap tools all work as well as the expensive ones, same as cues
just hurts alot less when they need to be replaced
take care of cheap tools and theyll do you well
 
JC said:
They are the good ones that are not expensive. Have tried those harbor freight ones. Great if you want them to switch to mm and zero mid measurement. Second time they do that I pitch them in the trash can. I don't currently possess any if that says anything.
Click to expand...
I have never had any re zero on their own.......... a few have failed after a few years............. toss it in the trash and buy another..........

Kim
 
JC said:
This has been discussed here before and I've purchased some real crap based on the discussions.

I have had one of these for several years and a ton of others in the same price range.

This one is best and it's not even close. Bought two more recently and threw all the other junk away. The are just as good as the first one.

www.ebay.com

iGaging Electronic Digital Caliper with Super Large Display for sale online | eBay

Find many great new & used options and get the best deals for iGaging Electronic Digital Caliper with Super Large Display at the best online prices at eBay! Free shipping for many products!
www.ebay.com www.ebay.com

You're welcome
Click to expand...
That's been essentially my favorite, so far.
In fact, have one screwed to the quill on one of my mills, for accurate down-feed increments and position.

However, 2 of mine have had issues with the battery holder. tends to pop-out or need shimmed or taped at some point, or it stops making contact. Partly because the rubber gasket is too flimsy and won't seat after it gets a little oil on it & swells.
Also they seem to disagree with my micrometers on larger measurements, but i never really qualified that. Its just a digital caliper, for cats sake.
When close enough to matter, the mics come out. Or if really fine, a comparater & gage blocks.

But yeah, impressed with the durability compared with others used in past & will still be the "next" one(s) i buy at this point.

smt
 
JC said:
This has been discussed here before and I've purchased some real crap based on the discussions.

I have had one of these for several years and a ton of others in the same price range.

This one is best and it's not even close. Bought two more recently and threw all the other junk away. The are just as good as the first one.

www.ebay.com

iGaging Electronic Digital Caliper with Super Large Display for sale online | eBay

Find many great new & used options and get the best deals for iGaging Electronic Digital Caliper with Super Large Display at the best online prices at eBay! Free shipping for many products!
www.ebay.com www.ebay.com

You're welcome
Click to expand...
Thanks, I just received that one.

Now, how about a recommendation for a scale?
 
LOL, I bought my HF calipers 15 years ago? Other then a cracked screen they still work perfect but I'm ready to have 3 or 4 in the shop so thanks @JC ;)
 
You must log in or register to reply here.
Back
Top