CNC Design

S

selkov

Registered
I posted this in the general forum in error....

I am new to this forum and this is my first attempt in building a CNC.
I am planning to build a stand alone unit with 4 axis's, probably from a Taig.
It was suggested to use Cuecut for the tapers and I think I might.
However I will also need some way to cut the pockets and the inlays.
Any suggestions on what I will need?

Thanks in advance for your help.
 
If you are asking about the software, many cuemakers including myself use BobCad and Mach 3 to do the design work and run the G code. There are more options of course, but I think these two are the most popular.

Good luck,
Alan

Phelps Custom Cues
 
To do inlays and pockets one needs programs for Computer-Aided Design, Computer-Aided Manufacturing, and CNC machine Motion Control. There are many options for each.

Many cuemakers use BobCad/Cam for the first two and Mach3 for the last.

I would suggest using Google and browsing CNC sites to pick up general CNC knowledge. YouTube has a plethora of videos for both programs to familiarize yourself with the capabilities and setup of the programs. Mach3 even has a free trial that only limits the length of code you can run.

~Beau
 
pescadoman said:
I'm going to be candid here. If you really need to ask that question then you ARE NOT yet qualified to build you own cnc....
Click to expand...

Is that not the whole point about asking questions?
When OTHER people give helpful answers then one can learn.
I have already learned alot on this subject thanks to members of this forum.
And I learned also to ignore you.
 
pescadoman said:
I'm going to be candid here. If you really need to ask that question then you ARE NOT yet qualified to build you own cnc....
Click to expand...

He keeps asking questions and receiving useful answers he will soon be educated and able to build the machine. Operate it? More questions and answers will be required.
 
selkov said:
Is that not the whole point about asking questions?
When OTHER people give helpful answers then one can learn.
I have already learned alot on this subject thanks to members of this forum.
And I learned also to ignore you.
Click to expand...

That could be a senseless mistake. Randy has more experience and knows more about designing and building a CNC machine than you will gain in the next two years of taking advice based solely on who you "like".

TW

 
Thomas Wayne said:


That could be a senseless mistake. Randy has more experience and knows more about designing and building a CNC machine than you will gain in the next two years of taking advice based solely on who you "like".

TW
Click to expand...
Possibly, But he does not seem inclined to share it.
 
selkov said:
Is that not the whole point about asking questions?
When OTHER people give helpful answers then one can learn.
I have already learned alot on this subject thanks to members of this forum.
And I learned also to ignore you.
Click to expand...

I apologize. George at XZero CNC has what he calls a Mini Raptor. It's a small footprint CNC that can be set on top of a workbench and would be able to satisfy all your needs. It's very well built and can be assembled in less than a day. Running, terminating wires, and building the controller takes longer.

I'm not sure what I have in mine, but I think it's less than 5 grand.

The belt driven 4th was a poor choice....
 
Some pics of the mini
 

Attachments

  • 20161109_141207.jpg
    20161109_141207.jpg
    194.1 KB · Views: 266
  • 20161109_141132.jpg
    20161109_141132.jpg
    192.3 KB · Views: 275
  • 20161109_141115.jpg
    20161109_141115.jpg
    189.7 KB · Views: 282
  • 20161109_141108.jpg
    20161109_141108.jpg
    188.8 KB · Views: 273
  • 20161109_141052.jpg
    20161109_141052.jpg
    191.5 KB · Views: 260
Randy, is that the 4th axis you were referring to being a poor choice? If so, why? I don't run one but the ones I've seen appeared pretty tight
 
You must log in or register to reply here.
Back
Top