Very Nice Barry Szamboti Shaft

poolrod

poolrod

I like old school
Silver Member
Made in 1994. Rolls straight. SOLD, thank you all.

12.2mm at the ferrule and just below it's a little smaller (12.0-12.1), weighs 3.7oz. Ivory ferrule.It will fit piloted stainless steel joint cues with a 0.840" joint diameter and a 0.520" pilot hole diameter (measurement on the brass insert).


 
Last edited:
Great opportunity here. My current player combines a cue butt from a now-infamous cuemaker with shafts from Barry Szamboti. As was the case in for my cue butt, many pilot holes on 5/16x14 butts are 0.500”. I chose to have the hole widened by a competent repairman, but sanding the pilot may also work. The combination works great and allows me to play in pool rooms with Szamboti shafts and not draw attention to my cue. At the price of a mass produced aftermarket LD, IMO, this is a no-brainer.
 
Sealegs50 said:
Great opportunity here. My current player combines a cue butt from a now-infamous cuemaker with shafts from Barry Szamboti. As was the case in for my cue butt, many pilot holes on 5/16x14 butts are 0.500”. I chose to have the hole widened by a competent repairman, but sanding the pilot may also work. The combination works great and allows me to play in pool rooms with Szamboti shafts and not draw attention to my cue. At the price of a mass produced aftermarket LD, IMO, this is a no-brainer.
Click to expand...

So true, this shaft is amazing too.:thumbup:
 
Are you sure about that Rod? I can not run a rack no matter what I play with....:smile:
Regards
Peter
 
Great Shaft! Easy to Modify To Fit Your Joss or Scruggs.

Sealegs50 said:
Great opportunity here. My current player combines a cue butt from a now-infamous cuemaker with shafts from Barry Szamboti. As was the case in for my cue butt, many pilot holes on 5/16x14 butts are 0.500”. I chose to have the hole widened by a competent repairman, but sanding the pilot may also work. The combination works great and allows me to play in pool rooms with Szamboti shafts and not draw attention to my cue. At the price of a mass produced aftermarket LD, IMO, this is a no-brainer.
Click to expand...


Bump for a great shaft, that can be easily sanded down to 0.500 in., in order to fit a Joss or Scruggs. I bought the other matching Szamboti shaft that Rod had, and it has a much firmer hit than the original shaft for my early 80's Scruggs Sneaky Pete. I can't wait to try the shaft out tonight with an older Joss cue that I have. Somebody take advantage of this great deal! You may have to wait until the next Cicada's hatch (17 years) to obtain one from Barry Szamboti. So get it while you can, from a great AZB member!
 
strum4u said:
Bump for a great shaft, that can be easily sanded down to 0.500 in., in order to fit a Joss or Scruggs. I bought the other matching Szamboti shaft that Rod had, and it has a much firmer hit than the original shaft for my early 80's Scruggs Sneaky Pete. I can't wait to try the shaft out tonight with an older Joss cue that I have. Somebody take advantage of this great deal! You may have to wait until the next Cicada's hatch (17 years) to obtain one from Barry Szamboti. So get it while you can, from a great AZB member!
Click to expand...

Thank you my friend, play well.
 
shaft

Hey Rod, If it mated up to my new cues I would snap it up. I have two more coming lets check it out when they get here if it is still here. Great Price Great Seller Randy
 
You must log in or register to reply here.
Back
Top