Anyone know where to get a MasterCue SuperTool

I have one and the leather case it came in. PM please and give me some time to respond, I had partial knee replacement last Friday and my daily schedule is pain and more pain followed up with therapy and some more pain.
Dan
 
They are made of solid brass, so be prepared for the extra weight in your case's pocket. Great tool, tho'!

Lisa
 
I got mine from Paul Gerni also...super nice guy....very difficulty tool to find....I bought 3 of 4 he had left about yrs ago...sold one...and kept the one Im currenlty using....the other is a backup....at the time I think I paid like 60.00 each. Good luck in the find.
 
I got mine from MasterCue directly back in 2000. It was a pretty pricey tool then. I think I paid somewhere like $40 for mine on an Introductory Special. Super nifty tool, can do it all, just about.

When I made the switch to layered tips, I found I was not using it as much, so I have been letting my ol' man use it over the last 5 years or so, as he prefers the single layer hard tips...he loves it.

On a rare occasion, I have seen them list on eBay...but they seem to go for a premium, even for the used ones.

Lisa
 
asiasdad said:
I bought one of those and wore a hole through the middle of the stone :mad: now I cannot replace it.

Danny, are you talking about the abrasive in the shaper? Have you considered perhaps checking out Lowes or Home Depot for some 'Non-Skid'? If I remember correctly, the grit in the 'Non-Skid' is similar to that which was in the shaper. You can buy it in either sticky backed strips for your stairs, or in a liquid form, usually applied to slick concrete garage floors. Might be worth checking out....if you can find a smaller quart sized can of the liquid application, that might be a good bet, because it will allow you to continue to replace the grit in the shaper.

Lisa
 
I was under the impression that they had been discontinued about 4 or 5 years ago now. But I'm old, and my memory may be faulty. :rolleyes: I think the one's that became available online after that was just NOS that the vendors had laying about. They're pretty much a matter of history now.

Lisa
 
My friend knows a dealer that has a bunch of these. I think for about $40 a piece. Send me a pm ACE911 and we can workout a deal.
 
mooseman i'm looking for a specific one, the same one as in the picture on the paul gerni website.
 
I see... I know the Super Tool I had was pretty much the same construction. Solid brass with the same features.

Definitely better than the Ultimate Tip Tool.

If you look at the TTMCST part number on the link it is identified as a Master Cue Super Tool.
 
wow

Would not mind having one of those .They do seem kinda
up there in price .If you find two for less than 50 a piece
let me know .
 
I looked at the one you are interested in and now I do notice the difference. Primarily the flat scuffer/file on the side. Other than that they are identical.....
 
Where is the mushroom trimmer on the tip tool? does it need refills like the Ultimate tip tool or does it last forever like a Williard Shaper?
 
Safety said:
Where is the mushroom trimmer on the tip tool? does it need refills like the Ultimate tip tool or does it last forever like a Williard Shaper?

The mushroom trimmer/burnisher is in the cone shaped area. When you twist it one way it trims, twist it the other way it burnishes. It does not require refills. It is actually similar to the willards as far as grit like abrasive.
 
I guess there must have been at least two versions of this tool as mine is not exactly like the one pictured in the link that ace911 supplied. Mine does not have abrasive on the side area and also has one large wheel located in the center of the top with two smaller wheels on either side.
Any other versions out there??
Dan
 
Back
Top