U sukkered me into it.BiG_JoN said:
Is this your setup?
can't imagine all the dust and chips in this place.
Last edited:
Ask The Cuemaker Topic
- Thread starter blud
- Start date
Is this your setup?
can't imagine all the dust and chips in this place.
guy
Joseph check your PM's from me.
blud
Joseph Cues said:Welcome back Blud.
Try not to hold up.
That picture also shows the maker puts his 3/8 stud into the forearm.
I don't see any phenolic ring at the bottom either.
What do you think of that?
This maker claims he doesn't take orders anymore.
Just get on his waiting list.
Yet, I have not seen any of his cues.
Joseph check your PM's from me.
blud
Blud, what is your favorite non-CNC lathe?
Thanks.
Thanks.
nope, that's not mine lol... mine is special... one of a kind, it looks rough, but it does as it is designed...Joseph Cues said:U sukkered me into it.
Is this your setup?
can't imagine all the dust and chips in this place.
thanks,
Jon
I'll take some pictures of it sometime.
Great going Jon. I'm sending you a Meucci shaft taper bar. lol
Blud, what do you think about this?
Kinda funny but I believe they mentioned about inserting tissue paper in there to prevent buzzing one time.
I don't see any phenolic ring.
How about putting the stud into the forearm?
That'd be great. CNC only or manual too?blud said:
Thanx.
Yes. Fat Larry taper.BiG_JoN said:
Now that you're ordering a CNC lathe, it might not matter.
Maybe you can machine me some titanium pins from now on.
hold it right there... i'm not ordering a CNC... a good friend of mine (who lives 5 mins away) ordered one, and will get it in oct. I will be able to use it if i want, (in exchange for some kick ass inlay designs) for making my own shafts (shaft taper) until i finish my tapering machine (have no idea when lol) and i could use it to make templets for the tapering machine... now why would you go around saying i'm getting CNC??? lol, i don't go around saying you have a thread mill, when you only have a ground nail...Joseph Cues said:Yes. Fat Larry taper.
Now that you're ordering a CNC lathe, it might not matter.
Maybe you can machine me some titanium pins from now on.
Thanks,
Jon
Wups... wasn't supposed to tell anybody about that special nail...
HI Mr. Blud
I have seen and use some of your cues. I think you build a good playing cue. My question is / is
there a cue maker that you look up to/ or one who you think was a Great cue Maker? If so, who
is he or she ? I was just curious because being an artist as myself ... I have looked at others work
and admire their gifts as well as my own. If you rather email me that would be fine. Thanks
I have seen and use some of your cues. I think you build a good playing cue. My question is / is
there a cue maker that you look up to/ or one who you think was a Great cue Maker? If so, who
is he or she ? I was just curious because being an artist as myself ... I have looked at others work
and admire their gifts as well as my own. If you rather email me that would be fine. Thanks
she?... are there any female cue makers?
Annie O makes cues.Buddha Jones said:
Ash Shafts
BLUD, HAVE YOU DONE ANYTHING WITH THE ASH CUES,AND SHAFTS SINCE VALLEY FORGE. WE SPOKE FOR A LITTLE WHILE ABOUT IT BUT YOU WERE VERY BUSY, SO I DIDN'T WANT TO BOTHER YOU. JUST CURIOUS. ALSO WOULD DEFLECTION BE MORE OR LESS THAN A MAPLE SHAFT WITH THE SAME FERRULE AND TIP ON IT?
blud said:
BLUD, HAVE YOU DONE ANYTHING WITH THE ASH CUES,AND SHAFTS SINCE VALLEY FORGE. WE SPOKE FOR A LITTLE WHILE ABOUT IT BUT YOU WERE VERY BUSY, SO I DIDN'T WANT TO BOTHER YOU. JUST CURIOUS. ALSO WOULD DEFLECTION BE MORE OR LESS THAN A MAPLE SHAFT WITH THE SAME FERRULE AND TIP ON IT?