How do you repair a mushroomed tip?

I'm surprised that so many of you have trouble with tips mushrooming. I've played pool since I was 11 and I don't think I've had it happen before. Maybe because I've never played with particularly soft tips. I just usually shape and burnish once in a while to keep it in shape. On a related note I've been looking at the Willard tip machine for replacing tips. I know it's expensive but might be cool to do tips for people. Does anyone know if it works with shafts under 12 mm though?
 
bbb said:
this works very well
you can buy them from andyho1984
they are priced fair as i remember but shipping was alot since they are shipped from the far east as i best recall...icbw
Click to expand...

Because he's based in Asia. Its the same when he buys stuffs from US. Shipping is always a b!tch.
 
StraightPoolIU said:
I'm surprised that so many of you have trouble with tips mushrooming. I've played pool since I was 11 and I don't think I've had it happen before. Maybe because I've never played with particularly soft tips. I just usually shape and burnish once in a while to keep it in shape. On a related note I've been looking at the Willard tip machine for replacing tips. I know it's expensive but might be cool to do tips for people. Does anyone know if it works with shafts under 12 mm though?
Click to expand...

Yes all sizes...
Here's a link...

http://www.muellers.com/Willard-Tipping-Machine-Replacement-Tip-Holder,522.html
 
I had lathe-like quality using a combination of the Pocket Lathe and the Joe Porper's Pool Mushroom Grazer Cue Tip Tool Trimmer.

With my one-handed chalking technique I only do a few swipes across the tip. My buddy does a one-handed chalk over the table for two minutes while he's trying to figure out the next shot.

I still like my avatar... so there.
 
I use one of those yellow carpenter-pencil-sharpeners to trim the walls of my tip. They only cost a few bucks and they work very well. You can trim the walls parallel to the shaft, but I give my tip walls a small angle (like a pencil tip)...that way the tip walls open to parallel as the tip gets broken in
 
Delaware Lar said:
I had lathe-like quality using a combination of the Pocket Lathe and the Joe Porper's Pool Mushroom Grazer Cue Tip Tool Trimmer.

With my one-handed chalking technique I only do a few swipes across the tip. My buddy does a one-handed chalk over the table for two minutes while he's trying to figure out the next shot.

I still like my avatar... so there.
Click to expand...

Glad you figured out your mushrooming problem. Honestly, patience is the only thing you need to fix a mushrooming tip. You can handle it with sandpaper or a nail file. :)

One handed chalking is great, all that matters is that you look at the tip and make sure it is covered in chalk. I honestly can't imagine a "two handed" chalking technique. :) I would have to try really hard to do that!
 
I took my cue to Triple Nines in Laurel, MD last. I had several miss cues. I showed my tip to a cue maker who was there. He noticed right away that I had a layered tip. He said that layered should be shaped on a lathe at at least 35rmp. And that trying to sand the shape on a layered tip was hard to do, and the tip was vulnerable to miss cue.

I tried scuffing the tip and I didn't miscue after that.

Anybody else have experience in shaping a layered tip?
 
I do all of mine by hand. Most times that I miss cue, is because I didn't stay down on the shot and make a smooth stroke
 
The Kiss said:
Get a laminated tip it will never shroom again.
Click to expand...

Depends on the brand and model. The several Kamui Soft Black tips I used have all had a bit of a mushroom on them and needed a bit of upkeep. I had an old school Moori back in the day and I think that one also mushroomed, the new Mooris did for sure and also played like doo doo. So far the only tip I have used that needed 0 touching to fix anything is the Ki-Tech one I got from Renfro.
 
Delaware Lar said:
I took my cue to Triple Nines in Laurel, MD last. I had several miss cues. I showed my tip to a cue maker who was there. He noticed right away that I had a layered tip. He said that layered should be shaped on a lathe at at least 35rmp. And that trying to sand the shape on a layered tip was hard to do, and the tip was vulnerable to miss cue.

I tried scuffing the tip and I didn't miscue after that.

Anybody else have experience in shaping a layered tip?
Click to expand...

Installing a layered tip is often different than a regular one, and the makers always provide instructions, the authorized resellers and installers should know exactly what tricks certain tips need. I had a cue maker install a Kamui Black for me once, that fell apart, he got another one from Kamui along with some notes and it never happened again. The Ki-Tech tip also had some special instruction although it's a single layer but treated, the cue maker followed those and that tip has been perfect ever since.
 
The Pocket Lathe put scratches and dings on my shaft. I took my Joss cue to Dan Janes. He made all the repairs at no charge. He suggested I give the Pocket Lathe to someone I don't like.
 
How do you repair a mushroomed tip?

Assumes that a mushroomed tip is a defect and harms your shooting.
Unwarranted assumption.
Illogical conclusion.

Peter Ebdon won the 2006 World Snooker Championship.
Here is a photo of his tip. :D
 

Attachments

  • peter ebdon tip.JPG
    peter ebdon tip.JPG
    45.4 KB · Views: 325
You must log in or register to reply here.
Back
Top