Is this a Bender Cue?

[evanhecht]

Hi Everyone

I traded some computer work for this cue but I don't have any info on the maker. I have been told it may be a Bender but I haven't been able to have Bender confirm this and there is no maker mark visible. Anyone out there know who made this cue?

Thanks for any info.

Regards

Evan

 

[HoldemRw]

Looks like a bender. He uses a,big pin like Cuetec 3/8x14 I think. Also usually has bender engraved on end of joint pin

Sent from my SAMSUNG-SM-G900A using Tapatalk

 

[Baron]

^^What he said. Should say Bender on the pin. Everything else looks legit.

 

[Murray Tucker]

Looks Bender inspired but I'm not convinced it is. Rings and points don't look quite right and the pin looks to be coarser than 14 tpi but it may be your pictures.

 

[JoeyInCali]

Looks Bender inspired but I'm not convinced it is. Rings and points don't look quite right and the pin looks to be coarser than 14 tpi but it may be your pictures.

Does the screw look 14TPI to you?
It looks a lot coarser to me.
Looks like 10TPI to me. I counted 10 threads.

 

[Murray Tucker]

Does the screw look 14TPI to you?
It looks a lot coarser to me.

I hit reply too quick. Look at my post again.

 

[JoeyInCali]

I hit reply too quick. Look at my post again.

Oops, my bad.

 

[HoldemRw]

If it's 3/8x10 I would lean toward it being a Alex brick. Or Coker cue they used similar ringwork and both used 3/8x10 as their main pin. Or at least I think I am no expert just had few cues over the years haha.

Sent from my SAMSUNG-SM-G900A using Tapatalk

 

[DJKeys]

Looks like a Brick to me as well, pin is not a Bender-

 

[ideologist]

Points look way off, wouldn't be surprised to find out it's an import

 

[cuenut]

Bryan Mordt?

 

[Duane Remick]

Bryan Mordt?

I also think BRYAN MORDT-
Send pics to him to confirm....
I DONT THINK MIKE BENDER

 

[ribdoner]

I also think BRYAN MORDT-
Send pics to him to confirm....
I DONT THINK MIKE BENDER

+ 1 on NOT Bender

 

[garczar]

I also think BRYAN MORDT-
Send pics to him to confirm....
I DONT THINK MIKE BENDER

I agree on the Mordt. The ring-work and the pin look like a BCM. Bryan makes his own modified 3/8x10 flat-bottom pins and this look s like one of his. He makes NICE stuff. Email BCM cues to be sure.

 

[imagemker]

I also think that looks like a BCM.

 

[garczar]

Mordt..............

I went back and looked at some BCM pics and Bryan's pins have a rounded nose and the cue in question looks like pin has a squarish, sharp edge. So this may not be a BCM. I'd still send him some pics just to rule it out.

 

[BryanMordt]

I went back and looked at some BCM pics and Bryan's pins have a rounded nose and the cue in question looks like pin has a squarish, sharp edge. So this may not be a BCM. I'd still send him some pics just to rule it out.

That looks like one of mine.

Bryan

 

[cuenut]

That looks like one of mine.

Bryan

Thanks for your input. Great looking cue. Whether your cues look like his or his look like yours, it is a compliment to both of you!

 

[evanhecht]

Thanks for all the replies. Especially Bryan Mordt.


Sent from my iPhone using AzBilliards Forums