Old Cue ID

MikeMaaen

AzB Silver Member
Silver Member
I have owned this cue since the late 70". It was originally purchased by me from Herb Lehman in Torrington Ct. Herb actually sold it to my wife as a Birthday Present for me and it came in a Fellini case which I also still have. I've tried to identify it through the Blue Book but, can't seem to find a really close match. There seems to be so much expertise on this forum I though someone might be able to take a look and see if they have any ideas on who the maker might have been. This is my first time on the forum and I have attempted to attach a photo however, I"m not sure it worked successfully. If not, I'll go back and try again. The cue is 19.5oz with 13mm shafts.

100_0369.jpg
 
Do you have any more photos that you could attach? Hopefully some closer photos of the point work, the joint, the butt sleeve, the bumper, the threads in the shaft? Thanks for any extra pictures that you have. Hopefully you will be able to find out quite a bit about this cue.

Good Luck!
 
Mike,
There is a ton of experience on here to draw from. As John said, if you can take clear, close-up pix of the cue, especially the points (both at the sharp end and at the base), the joint (make sure the threads and pilot shows), the butt and bumper, and if possible, remove the bumper and show how it is made inside. The more photos, the better the chance for an ID.
Joe
 
MikeMaaen said:
I have owned this cue since the late 70". It was originally purchased by me from Herb Lehman in Torrington Ct. Herb actually sold it to my wife as a Birthday Present for me and it came in a Fellini case which I also still have. I've tried to identify it through the Blue Book but, can't seem to find a really close match. There seems to be so much expertise on this forum I though someone might be able to take a look and see if they have any ideas on who the maker might have been. This is my first time on the forum and I have attempted to attach a photo however, I"m not sure it worked successfully. If not, I'll go back and try again. The cue is 19.5oz with 13mm shafts.

At a glance, it looks more like an ADAM than anything else - tho
a Fellini would be kinda sporty for one. If it is an ADAM,
the pin will be 5/16 - 18. Viking is also a possibility, from that
time period a Viking would have 3 points.

If the pin is anything other than 5/16 - 18, that automaticaly rules
out both Adam and Viking.

A 5/16 -14 pin(most likely alternative) would tend toward a small
volume, custom maker.

HTH
Dale
 
Took a couple of days to put some additional photos together. Thanks to all that responded earlier. I hope these will give someone a little better idea of what it is?? Your help is always appreciated.
 

Attachments

  • 100_0841.jpg
    100_0841.jpg
    57.5 KB · Views: 325
  • 100_0842.jpg
    100_0842.jpg
    66.1 KB · Views: 335
  • 100_0846.jpg
    100_0846.jpg
    66.8 KB · Views: 307
  • 100_0847.jpg
    100_0847.jpg
    56.1 KB · Views: 307
More Pictures of Old Cue

Finally broke the code and got some additional photos that you guys asked for. Any help in identification would be most appreciated.
100_0835.jpg

100_0836.jpg

100_0837.jpg

100_0839.jpg

100_0840.jpg
 
I am probably off but it has similar characteristics to an old Mali cue that I own.
The pins have a similar shape and the rounded edges of the buttcaps seem to sorta match.

I have been told that mine is from the 1970-1972 catalog.

Perhaps an older Mali?
 

Attachments

  • old1.jpg
    old1.jpg
    54.4 KB · Views: 236
  • old2.jpg
    old2.jpg
    44.6 KB · Views: 229
I can tell you what it's not !!
It's not a cheap cue !!
Contact Tate looks like a custom old Palmer to me ..
 
Thats funny, I have an old Rich as well . . .
here is the joint on it for comparison . . .
 

Attachments

  • older1.jpg
    older1.jpg
    46.7 KB · Views: 448
Hints of an old 1st generation Adam

I could be so far off base, everyone snorts in laughter. The Points and veneers and full splice remind me of an old Adam I had. The joint screw looks like an old Adam that has had the pointed end ground down. This makes me think it might be a very very early Adam maybe near protottype stage where either the factory or someone modified it to remove the point. The screw in the butt is a Philips head which is like an old Adam cue I had IF it is a weight screw. That you might want to check. Mine was an alloy weight screw.

If the wrap is nylon instead of Irish linen, then I would say it is for sure an old Adam, except Rich had nyon wraps as well.

I will be the first to admit I could be on the moon with this, but some of the characteristics are similar.

the biggest problem is the inserts in the shafts. Never seen any like those anywhere.
 
Last edited:
Thanks

Sounds like a Mali, Adam, early prototype? The wrap is irish linen and although I have tried to loosen the screw in the butt it does not want to be removed so I've tended to leave it alone. I've never seen the inserts in the shafts done quite like this and can only guess aat the age of the cue. I think I got it in 1982 just before the New England Straight Pool Championships in New London Ct. Does any of that help?? Thanks for looking and trying to help with the ID.
 
Last post on this Old Cue

Thanks for all the help in trying to identify this cue. Seems we're still in a quandry as to the maker for sure but in any case.... if anyone is interested I'll take $450 for it. Four points, rolls straight and hits great. 19 OZ with (I think) one 12 and one 13 MM shaft with pro taper.
 
MikeMaaen said:
Thanks for all the help in trying to identify this cue. Seems we're still in a quandry as to the maker for sure but in any case.... if anyone is interested I'll take $450 for it. Four points, rolls straight and hits great. 19 OZ with (I think) one 12 and one 13 MM shaft with pro taper.

HOW MUCH WITH THE CASE?
 
For Sale

Thanks for everyones input into what type of cue this is. Seems like we did not get a definitive answer but, in any case, this is my last post on this item so if anyone is interested in purchasing a mystery cue I'll take $400 for it with two shafts. No paypal on this end so contact me by pm and we'll work out payment etc. I'll ship free in US. Again, thanks for all the time you spent trying to determine the maker. It's a good hitting stick but, my Dick Black won my vote on what to keep.
 
Back
Top