Possible matching set

[xpatcan1]

I am going to be ordering another cue soon and I think I want a matching set (player, breaker and a matching jumper)

This is what I have come up with so far using MS paint, I am getting really good at cut and paste .

I am looking for some ideas for the forearm section of the player and just some opinions on the design so far.

 

[runout1961]

Hey Buddy, I like your idea. The cues you have come up with look pretty damn nice. I did the same thing with my player. I have a clean classic looking rosewood Jensen cue. I liked it so much I sent it to Mike to have an exact replica j/b made. The j//b is an EXACT match of my player. The only difference is the black ring above the wrap where it breaks apart and the two tips for the j/b are phenolic. While it was there I had another shaft made for the player. Player-3 shafts, J/B-2shafts. Sorry the pics aren't the best but it's what I have to work with right now. So needless to say I am a fan of the matched set.

John

 

[Realizm]

Hey Buddy, I like your idea. The cues you have come up with look pretty damn nice. I did the same thing with my player. I have a clean classic looking rosewood Jensen cue. I liked it so much I sent it to Mike to have an exact replica j/b made. The j//b is an EXACT match of my player. The only difference is the black ring above the wrap where it breaks apart and the two tips for the j/b are phenolic. While it was there I had another shaft made for the player. Player-3 shafts, J/B-2shafts. Sorry the pics aren't the best but it's what I have to work with right now. So needless to say I am a fan of the matched set.

John

Get kenny murrell.

 

[xpatcan1]

Get kenny murrell.

thats the plan, he is easy to work with, his prices are very very good! and he can build just about anything i want in a cue!

 

[RascalDoc]

Wow!!

Thats a hell of a design and a GREAT job doing it!!!!!!!!!!!! Doing the photos I mean ...

 

[xpatcan1]

Thats a hell of a design and a GREAT job doing it!!!!!!!!!!!! Doing the photos I mean ...

thanks i am still working on the top half but i really cant get what i want using ms paint,,,

 

[FAST_N_LOOSE]

I am going to be ordering another cue soon and I think I want a matching set (player, breaker and a matching jumper)

This is what I have come up with so far using MS paint, I am getting really good at cut and paste .

I am looking for some ideas for the forearm section of the player and just some opinions on the design so far.

I'D DO IT DIFFERENTLY......

USE THE BACKEND DESIGN IN THE NOSE. AND DO FLOATING BOXES IN THE BUTT. (I'M NOT A FAN OF REVERSE POINTS.

 

[mosconiac]

If you truly did those in MS Paint...D@MN! You've got some skills!

 

[xpatcan1]

If you truly did those in MS Paint...D@MN! You've got some skills!

honest it wasnt that hard just took time,,,, i just cut and paste pics of all kinds of cues wood and ring work. you can change your cut-outs a bit like stretch them or squash them, that helps a little bit. notice the pics i made dont taper,,, its really hard to get a taper or points using mspaint.

 

[xpatcan1]

I'D DO IT DIFFERENTLY......

USE THE BACKEND DESIGN IN THE NOSE. AND DO FLOATING BOXES IN THE BUTT. (I'M NOT A FAN OF REVERSE POINTS.

that sounds good! i will do up a pic and post it.

i am a huge fan of reverse points or point in general! my last cue kinda pointed me out so i might try a box cue.

 

[poohkiller]

Here is a sketch that I could come up with. Nevermind the rings/dots inside the points, those could be in between the points up-side-down or whatever.

I am bad at drawing - and have always been - so bear with me. Let me know what you think.