Simonis

iownthe412

AzB Silver Member
Silver Member
Anyone ever had an issue with being short on Simonis 860? I ordered a pre-cut cloth from them and when I went to felt the rails I was about 3 rails to short. I don't think it is humanly possible to stretch the cloth tighter than it is. Has anyone ever had this issue? If so, what should I do?
 
Anyone ever had an issue with being short on Simonis 860? I ordered a pre-cut cloth from them and when I went to felt the rails I was about 3 rails to short. I don't think it is humanly possible to stretch the cloth tighter than it is. Has anyone ever had this issue? If so, what should I do?

First question you might want to answer is did you order the Simonis from Simonis directly....or buy it through some other source? If not from Simonis directly...then I don't see this as a Simonis problem...do you?

Glen
 
It was an additional source. I guess I obviously have to order some additional cloth for the rails. I was not placing blame on anyone. Maybe I did the cloth wrong, but like I said I don't think it would have been possible to stretch it any tighter. It is my first time re-covering a table and I took my time and made sure I did everything right.
 
Where the strips for the rails 12" wide?

If so, they should be cut into 6" strips.
 
Apparently the cloth was cut off of a 62" bolt rather than 66". So I was shorted a bit of cloth. I understand that its sometimes better to have a professional handle these things but I wanted to learn and what better way to do that than with my own table and good old trial and error. Simonis is correcting the problem so no worries on my end. Everything went smooth up until this point so I guess I can be happy with that.
 
Apparently the cloth was cut off of a 62" bolt rather than 66". So I was shorted a bit of cloth. I understand that its sometimes better to have a professional handle these things but I wanted to learn and what better way to do that than with my own table and good old trial and error. Simonis is correcting the problem so no worries on my end. Everything went smooth up until this point so I guess I can be happy with that.

You need to get back with whom ever you bought the Simonis from and call "BS"...Simonis only has cloth made in two widths...66" and 78"...and as far as "Simonis" correcting the problem...there was NO problem on Simonis's end;)

Glen

PS. I'm not jumping on you or anything like that, I just don't feel right when "Simonis's" name is used in association with problems like this if and when they happen.
 
Last edited:
Simisos sucks these days, it is a shame too, they area great company that has been a big part of cue sports for ever, why they have destroyed the product is beyond me(specifically green 860)
 
Simisos sucks these days, it is a shame too, they area great company that has been a big part of cue sports for ever, why they have destroyed the product is beyond me(specifically green 860)

I'm aware of all the changes Simonis has made since when I first started using it back in 1984...which would put you at about 14-15 years old at the time, and that's back before there even was an 860 Simonis. So, other than Simonis's 860Hr at the time they introduced that, which was a thicker weave of the 760 70%wool/30%nylon but was promoted as a humidity resistant cloth, until the newer 860HR.."high resistant" used today, Simonis has not changed the building blocks of the 860 Green since they first introduced it as a 90%wool/10%nylon weave. So, needless to say, I'm a little lost at your dislike of the 860 Green Simonis today as if Simonis has changed it in some way, because it's not been changed other than what I have described.

Maybe the change has been in the balls, or maybe you're just getting senile in your old age:p:D

Glen
 
I'm aware of all the changes Simonis has made since when I first started using it back in 1984...which would put you at about 14-15 years old at the time, and that's back before there even was an 860 Simonis. So, other than Simonis's 860Hr at the time they introduced that, which was a thicker weave of the 760 70%wool/30%nylon but was promoted as a humidity resistant cloth, until the newer 860HR.."high resistant" used today, Simonis has not changed the building blocks of the 860 Green since they first introduced it as a 90%wool/10%nylon weave. So, needless to say, I'm a little lost at your dislike of the 860 Green Simonis today as if Simonis has changed it in some way, because it's not been changed other than what I have described.

Maybe the change has been in the balls, or maybe you're just getting senile in your old age:p:D

Glen


thanks for the complement but I was 18 back then, i'm older than I look most of the time. I played for 3 years before the Simonis invasion it was all 760(I remember that as well), I remember when no pool rooms had it and within a year they all did, I remember that like yesterday, hell I could name off the order the rooms switched over to Simonis,

I know they havent changed the blend of 90/10 or the weave, what thay have done in the last few years is they are cutting more nap off, which speeds up the cloth and is causing more skids and ball jumps than ever, their older product didnt do this. period.

I will email you a pic that John Broomback took of me bakining a ball the shot was staged, he accidentally shot the picture BEFORE either ball hit the cushon, I didnt shoot hard or intend to make the ball as it was just staged, the balls jumped, he caught it-you wont believe it, when I show you inperson how soft I hit the ball its even more amazing. it had the energy to climb up on the ball, the table wasnt clean nor dirty, perhaps 3 hours play time.


Botton line is they had it right and in a effort to make it better(or cheaper) they managed to screw it up. I was just playing on a table thats had some use that has Simonis from around 2000 on it, it looked EXACTLY like the 860 I had put on my GC4(the box you moved to Co), when I moved it from my other house to the current house When they took it down I told them to keep the old cloth as part of the moving $$$, I wish I had it to show you, you would see that the "Fuzz" above the weave it longer/thicker. Its not like that now and thats ok, if It didnt skid constantly.

There is alot more I would like to say about this but cant because of business reasons etc. lets just say I'm not alone in my opinion here.


best
eric
 
glen,

please fire off a email to me at EP90210@hotmail.com


somehow I lost your email addy, I am senile you know:o

take care buddy,

looking foward to seeing you again.

best


eric
 
Anyone ever had an issue with being short on Simonis 860? I ordered a pre-cut cloth from them and when I went to felt the rails I was about 3 rails to short. I don't think it is humanly possible to stretch the cloth tighter than it is. Has anyone ever had this issue? If so, what should I do?

Your post is a bit confusing.

A precut means you should have received 6 pieces for the rails plus the slate piece.
When you say "3 rails short" do you mean you received only 3 rail pieces?

Simonis bolts come in 66" and 78" widths. The table size determines which size bolt is used for a precut.
What size is your table?
 
Your post is a bit confusing.

A precut means you should have received 6 pieces for the rails plus the slate piece.
When you say "3 rails short" do you mean you received only 3 rail pieces?

Simonis bolts come in 66" and 78" widths. The table size determines which size bolt is used for a precut.
What size is your table?

I received the bed cloth which really only had enough cloth for the bed and 1 rail. I also received a 12" wide sheet cut in the middle at one end which would be for 2 rails. The 66" bolt is what they would use for an 8' table correct? The only other felt I used extra was for pocket liners and they were pretty much just scraps so theres no way they sent me the right amount.
 
I received the bed cloth which really only had enough cloth for the bed and 1 rail. I also received a 12" wide sheet cut in the middle at one end which would be for 2 rails. The 66" bolt is what they would use for an 8' table correct? The only other felt I used extra was for pocket liners and they were pretty much just scraps so theres no way they sent me the right amount.

Yes, a 66" bolt is used for an 8' (and a 7') table. The slate piece should be 54" X 100".
4 rail pieces would come off the side (12" X 100" piece split down the middle and cut in half).
2 more pieces would need to be cut from the bolt (lengthwise) and added to make the 6 total rail pieces.
Appears whoever you got the cloth from didn't know what they were doing.
 
Back
Top