Got my lathe together today

TomHay

TomHay

Best Tips For Less
Silver Member
You are looking at the Unique Products Cue Maker with Taper Shaper add on. I will be changing the shaft taper bar, not anything wrong with thiers I just want my old own taper.

I like how you can flip taper bar to v grove ForeArms and can picture v grove on butt sleeves.

Tomorrow I finish tweak and start cutting big smaller. I don't fish so retirement brings me back to labor of love.

1newlathe setup.jpg
 
Thank you. Hopefully my itch is scratched, LOL but everyone knows how that goes.
 
Congrats Tom.
You need a dust containment box Tom.
That room will get nasty fast w/out a dust box.
Put a pair of stoppers on that taper bar then set your own bar.
Been there done that.
Epoxy some metal sheet strategically under the router so you can use an indicator with magnetic base.
 
Joey, thanks for the tips. I was thinking of a 5HP shop vac connected to pvc with holes in it. Any suggestions and input more than appreciated.
 
TomHay said:
Joey, thanks for the tips. I was thinking of a 5HP shop vac connected to pvc with holes in it. Any suggestions and input more than appreciated.
Click to expand...

http://www.gosale.com/4121245/hoover-l2310-the-guv-garage?gclid=CMXv_aTZ-64CFSoGRQod60P7yQ
http://www.rockler.com/product.cfm?page=31104
Those two will get your shop so much more quiet.
Disposing of the dust and chips will be easier too.
You can also run the exhaust of that vacuum to outside of the shop.

Build an airtight box but with filter for incoming air.
http://forums.azbilliards.com/showthread.php?t=227655&highlight=dust
Kenny did one there.
 
You definitely want an enclosure to contain the dust, here is a pic of my enclosure I just finished for my Taper shaper. :smile:
 

Attachments

  • taper.jpg
    taper.jpg
    33.2 KB · Views: 924
Man, you guys kick butt. I can't tell you how much I appreciate it. Yall did everything but build it for me.:bow-down:
 
Tom,

You're off to a good "re-start" - keep it up!!

:smile:

Gary
 
dust box

JoeyInCali said:
Congrats Tom.
You need a dust containment box Tom.
That room will get nasty fast w/out a dust box.
Put a pair of stoppers on that taper bar then set your own bar.
Been there done that.
Epoxy some metal sheet strategically under the router so you can use an indicator with magnetic base.
Click to expand...

let me know when you get one made...I'm in process and need ideas or one already built...
thanks, Bill
 
I seen the enclosure Cue built for his and it cut the noise down to half or less as well.
 
I like everything I see. I think I will build mine from Urethane Foam, being light weight and more soud proof and apply a Hard Coat Polyurea inside and out. This would be the same type coating they use in theme parks to make Polystyrene rock like and hard.
 
I'd use Viagra paint instead Tom.
Hey, it is on the market, its true.
Just the other day I was at the bar and they were offering Viagra shooters.
The waitress told me she could pour me a stiff one.
 
LOL Blue Hog, I aint wasting my Viagra script on wood, my Dr. only allows me to have so many a month as it is. :smile:
 
Hey Tom NICE pick up.:thumbup: Id like to ask a question if you dont mind. Im about to make a decision on a lathe. What prompted you to get the Unique over the others?
 
TomHay said:
You are looking at the Unique Products Cue Maker with Taper Shaper add on. I will be changing the shaft taper bar, not anything wrong with thiers I just want my old own taper.

I like how you can flip taper bar to v grove ForeArms and can picture v grove on butt sleeves.

Tomorrow I finish tweak and start cutting big smaller. I don't fish so retirement brings me back to labor of love.

View attachment 219264
Click to expand...



What did it cost?

By the way nice looking lathe:smile:
 
You must log in or register to reply here.
Back
Top